2009 Polaris Ranger 6x6 700 EFI Owners Manual - Page 95

2009 Polaris Ranger 6x6 700 EFI Manual

Get 2009 Polaris Ranger 6x6 700 EFI PDF manuals and user guides View all 2009 Polaris Ranger 6x6 700 EFI manuals

Page 95 highlights

MAINTENANCE Lights Headlight Beam Adjustment X 25 ft. (7.6 m) X 8" (20 cm) 1. Place the vehicle on a level surface with the headlight approximately 25 ft. (7.6 m) from a wall. 2. Measure the distance from the floor to the center of the headlight and make a mark on the wall at the same height. 3. Apply the brakes. Start the engine. Turn on the headlights. 4. Observe the headlight aim. The most intense part of the headlight beam should be aimed 8" (20 cm) below the mark placed on the wall. Include the weight of a rider on the seat while performing this step. 5. If the headlight needs adjustment, open the hood. The lights are part of the hood assembly. 6. Turn the adjustment screw to Adjustment Screw adjust the beam. 7. Close the hood. Repeat steps View of driver's headlight with hood lifted. 4-6 until the beam is properly adjusted. Brake Lights When the brake pedal is depressed, the console brake light comes on. Check the brake light before each ride. 1. Turn the ignition switch to the ON position. 2. Depress the brake pedal. The brake light should come on after about 10 mm (0.4 in.) of pedal travel. If the light doesn't come on, check the bulb. 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
92
MAINTENANCE
Lights
Headlight Beam Adjustment
1.
Place the vehicle on a level surface with the headlight approxi-
mately 25 ft. (7.6 m) from a wall.
2.
Measure the distance from the floor to the center of the headlight
and make a mark on the wall at the same height.
3.
Apply the brakes. Start the engine. Turn on the headlights.
4.
Observe the headlight aim. The most intense part of the headlight
beam should be aimed 8" (20 cm) below the mark placed on the
wall. Include the weight of a rider on the seat while performing this
step.
5.
If the headlight needs adjust-
ment, open the hood. The
lights are part of the hood
assembly.
6.
Turn the adjustment screw to
adjust the beam.
7.
Close the hood. Repeat steps
4-6 until the beam is prop-
erly adjusted.
Brake Lights
When the brake pedal is depressed, the console brake light comes on.
Check the brake light before each ride.
1.
Turn the ignition switch to the ON position.
2.
Depress the brake pedal. The brake light should come on after about
10 mm (0.4 in.) of pedal travel. If the light doesn't come on, check
the bulb.
25 ft.
(7.6 m)
8" (20 cm)
X
X
Adjustment
Screw
View of driver’s headlight with hood lifted.