3Com 3C81600 User Guide - Page 30

Power Cord Set, This unit operates under SELV conditions Safety Extra Low

Get 3Com 3C81600 - SuperStack II Enterprise Monitor PDF manuals and user guides View all 3Com 3C81600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

30 APPENDIX A: SAFETY INFORMATION determine loading limitations. It is important that the loading limitations are not exceeded. s Connect the unit to an earthed power supply to ensure compliance with safety standards. s It is essential that the socket outlet is installed near to the unit and is easily accessible. You can only disconnect the unit by removing the supply plug from the outlet. s If installing the Advanced RPS Chassis in a stack with SuperStack units, place the Advanced RPS Chassis at the bottom of the stack. s This unit operates under SELV conditions (Safety Extra Low Voltage) according to IEC 60950, the conditions of which are maintained only if the equipment to which it is connected also operates under SELV. s The appliance coupler (the connector to the device itself and not the wall plug) must have a configuration for mating with an EN60320/IEC320 appliance inlet. s Use only the special cables designed and supplied for this product. s Power Cord Set: This must be approved for the country where it is used: U.S.A. and Canada United Kingdom only s The cord set must be UL-approved and CSA certified. s The minimum specification for the flexible cord is: No. 18 AWG Type SV or SJ 3-conductor s The cord set must have a rated current capacity of at least 10A. s The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V) configuration. s The supply plug must comply with BS1363 (3-pin 13 amp) and be fitted with a 5A fuse which complies with BS1362. s The mains cord must be or marked and be of type H03VVF3GO.75 (minimum).

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
30
A
PPENDIX
A: S
AFETY
I
NFORMATION
determine loading limitations. It is important that the loading
limitations are not exceeded.
■
Connect the unit to an earthed power supply to ensure
compliance with safety standards.
■
It is essential that the socket outlet is installed near to the unit
and is easily accessible. You can only disconnect the unit by
removing the supply plug from the outlet.
■
If installing the Advanced RPS Chassis in a stack with
SuperStack units, place the Advanced RPS Chassis at the
bottom of the stack.
■
This unit operates under SELV conditions (Safety Extra Low
Voltage) according to IEC 60950, the conditions of which are
maintained only if the equipment to which it is connected also
operates under SELV.
■
The appliance coupler (the connector to the device itself and not
the wall plug) must have a configuration for mating with an
EN60320/IEC320 appliance inlet.
■
Use only the special cables designed and supplied for this
product.
■
Power Cord Set:
This must be approved for the country where it is used:
U.S.A. and
Canada
■
The cord set must be UL-approved and CSA certified.
■
The minimum specification for the flexible cord is:
No. 18 AWG
Type SV or SJ
3-conductor
■
The cord set must have a rated current capacity of at least
10A.
■
The attachment plug must be an earth-grounding type with
a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V)
configuration.
United
Kingdom
only
■
The supply plug must comply with BS1363 (3-pin 13 amp)
and be fitted with a 5A fuse which complies with BS1362.
■
The mains cord must be <HAR> or <BASEC> marked and
be of type H03VVF3GO.75 (minimum).