AEG L75480WD Product Manual - Page 32

The laundry is full

Get AEG L75480WD PDF manuals and user guides View all AEG L75480WD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

32 www.aeg.com Problem Possible cause Possible solution The appliance fills The end of the drain with water and hose is too low. drain immediately. Make sure that the drain hose is in the correct position. The washing re- The detergent you used Increase the detergent quantity sults are not satis- was not sufficient or cor- or use a different one. factory. rect. You did not remove the Use special products to remove stubborn stains before the stubborn stains. you wash the laundry. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. The appliance does not dry or does not dry correctly. The water tap is not turned on. Turn the tap on. The drain filter is clogged. Clean the drain filter. There is too much laun- Reduce the laundry load. dry in the drum. You have set a wrong dryness level or drying time. Set additional drying time. The laundry is full of different colours fluff. The fabrics washed in the cycle before released fluff of different colours. • The drying phase helps to remove some fluff. • Clean the laundry with a fluff remover. If there is a big quantity of fluff in the drum repeat this procedure again and again: • Clean the empty drum, the gasket and the door with a wet cloth. • Set a rinse cycle • Put a wool or piled fabric cloth in the drum. • Set a drying cycle of 10 minutes • Remove the old wool cloth. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the service centre. If the display shows other alarm codes, contact the service centre.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
Problem
Possible cause
Possible solution
The appliance fills
with water and
drain immediately.
The end of the drain
hose is too low.
Make sure that the drain hose is
in the correct position.
The washing re-
sults are not satis-
factory.
The detergent you used
was not sufficient or cor-
rect.
Increase the detergent quantity
or use a different one.
You did not remove the
stubborn stains before
you wash the laundry.
Use special products to remove
the stubborn stains.
Incorrect temperature
was set.
Make sure that you set the cor-
rect temperature.
Too much laundry load.
Decrease the laundry load.
The appliance
does not dry or
does not dry cor-
rectly.
The water tap is not
turned on.
Turn the tap on.
The drain filter is clog-
ged.
Clean the drain filter.
There is too much laun-
dry in the drum.
Reduce the laundry load.
You have set a wrong
dryness level or drying
time.
Set additional drying time.
The laundry is full
of different colours
fluff.
The fabrics washed in the
cycle before released
fluff of different colours.
•
The drying phase helps to re-
move some fluff.
•
Clean the laundry with a fluff
remover.
If there is a big quantity
of fluff in the drum re-
peat this procedure
again and again:
•
Clean the empty drum, the
gasket and the door with a wet
cloth.
•
Set a rinse cycle
•
Put a wool or piled fabric cloth
in the drum.
•
Set a drying cycle of 10 mi-
nutes
•
Remove the old wool cloth.
After the check, activate the appliance.
The programme continues from the point
of interruption.
If the problem occurs again, contact the
service centre.
If the display shows other alarm codes,
contact the service centre.
32
www.aeg.com