ASRock Z77 Extreme9 User Manual - Page 51

Chassis and Power Fan Connectors

Get ASRock Z77 Extreme9 PDF manuals and user guides View all ASRock Z77 Extreme9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

system is in S1/S3 sleep state. The LED is off when the system is in S4 sleep state or powered off (S5). HDLED (Hard Drive Activity LED): Connect to the hard drive activity LED on the chassis front panel. The LED is on when the hard drive is reading or writing data. The front panel design may differ by chassis. A front panel module mainly consists of power switch, reset switch, power LED, hard drive activity LED, speaker and etc. When connecting your chassis front panel module to this header, make sure the wire assignments and the pin assign-ments are matched correctly. Chassis Speaker Header (4-pin SPEAKER 1) (see p.14, No. 21) Please connect the chassis speaker to this header. Power LED Header (3-pin PLED1) (see p.14, No. 19) 1 PLEDPLED+ PLED+ Please connect the chassis power LED to this header to indicate system power status. The LED is on when the system is operating. The LED keeps blinking in S1/S3 state. The LED is off in S4 state or S5 state (power off). Chassis and Power Fan Connectors (4-pin CHA_FAN1) (see p.14, No. 31) CHA_FAN_SPEED +12V GND FAN_SPEED_CONTROL (3-pin CHA_FAN2) (see p.14, No. 30) Please connect the fan cables to the fan connectors and match the black wire to the ground pin. CHA_FAN1, CHA_FAN2 and CHA_FAN3 support Fan Control. (3-pin CHA_FAN3) (see p.14, No. 46) (3-pin PWR_FAN1) (see p.14, No. 3) 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
51
Chassis Speaker Header
Please connect the chassis
(4-pin SPEAKER 1)
speaker to this header.
(see p.14,
No. 21)
system is in S1/S3 sleep state. The LED is off when the system is in S4
sleep state or powered off (S5).
HDLED (Hard Drive Activity LED):
Connect to the hard drive activity LED on the chassis front panel. The LED
is on when the hard drive is reading or writing data.
The front panel design may differ by chassis. A front panel module mainly
consists of power switch, reset switch, power LED, hard drive activity LED,
speaker and etc. When connecting your chassis front panel module to this
header, make sure the wire assignments and the pin assign-ments are
matched correctly.
Power LED Header
Please connect the chassis
(3-pin PLED1)
power LED to this header to
(see p.14,
No. 19)
indicate system power status.
The LED is on when the system
is operating. The LED keeps
blinking in S1/S3 state. The
LED is off in S4 state or S5
state (power off).
1
PLED+
PLED+
PLED-
Chassis and Power Fan Connectors
Please connect the fan cables
(4-pin CHA_FAN1)
to the fan connectors and match
(see p.14,
No. 31)
the black wire to the ground pin.
CHA_FAN1, CHA_FAN2 and
CHA_FAN3 support Fan
(3-pin CHA_FAN2)
Control.
(see p.14,
No. 30)
(3-pin CHA_FAN3)
(see p.14,
No. 46)
(3-pin PWR_FAN1)
(see p.14,
No. 3)
GND
+12V
CHA_FAN_SPEED
FAN_SPEED_CONTROL