Adaptec 2400A Installation Guide - Page 56

Installing the Driver for a Boot Controller in a New NetWare4.2 Server, Ctrl+A, Enter

Get Adaptec 2400A - ATA RAID Controller PDF manuals and user guides View all Adaptec 2400A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Installing the Driver 3 Shutdown the server. 4 Install and configure your Adaptec RAID controller as a secondary controller according to the instructions in Chapter 2. Note the slot occupied by the controller; you will need this information later in the install process. 5 Start up the server. During restart, press Ctrl+A to start SMOR. Use SMOR to create the RAID. For details, refer to Using SMOR on page 2-10. 6 Start NetWare. 7 When the console prompt appears, type load install and press Enter. 8 Select Product Options and press Enter. 9 Select Install a Product Not Listed and press Enter. 10 Insert the disk you created in Step 2 and install I2O and Block Storage support only. 11 Accept the defaults for the remaining install options. 12 Return to the main install screen and select NCF Options. 13 Select Edit startup.ncf. If needed, edit the file so that i2opci.nlm is listed before bkstrosm.ham in your startup.ncf file. 14 Shutdown and restart the server. Installing the Driver for a Boot Controller in a New NetWare 4.2 Server In this scenario, you are installing an Adaptec RAID controller as the boot controller in a new NetWare 4.2 server. To install the driver 1 Create a driver floppy disk using the Adaptec RAID Installation CD. To create the disk a Insert the Adaptec RAID Installation CD in your drive and a blank floppy disk in the floppy disk drive. b Copy all the files in \packages\netware\4.2\driver to the floppy disk. 3-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
3-21
Installing the Driver
3
Shutdown the server.
4
Install and configure your Adaptec RAID controller as a
secondary controller according to the instructions in
Chapter 2
.
Note the slot occupied by the controller; you will need this
information later in the install process.
5
Start up the server. During restart, press
Ctrl+A
to start SMOR.
Use SMOR to create the RAID. For details, refer to
Using
SMOR
on page 2-10
.
6
Start NetWare.
7
When the console prompt appears, type
load
install
and
press
Enter
.
8
Select
Product Options
and press
Enter
.
9
Select
Install a Product Not Listed
and press
Enter
.
10
Insert the disk you created in
Step 2
and install I
2
O and Block
Storage support only.
11
Accept the defaults for the remaining install options.
12
Return to the main install screen and select
NCF Options.
13
Select
Edit startup.ncf
. If needed, edit the file so that
i2opci.nlm
is listed before
bkstrosm.ham
in your
startup.ncf
file.
14
Shutdown and restart the server.
Installing the Driver for a Boot Controller in a New
NetWare 4.2 Server
In this scenario, you are installing an Adaptec RAID controller as the
boot controller in a new NetWare 4.2 server. To install the driver
1
Create a driver floppy disk using the
Adaptec RAID Installation CD
.
To create the disk
a
Insert the
Adaptec RAID Installation CD
in your drive and a
blank floppy disk in the floppy disk drive.
b
Copy all the files in
\packages\netware\4.2\driver
to the floppy
disk.