Adaptec 2400A Installation Guide - Page 62

Installing the Driver in a New OpenServer5.0x System

Get Adaptec 2400A - ATA RAID Controller PDF manuals and user guides View all Adaptec 2400A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

Installing the Driver Installing the Driver in a New OpenServer 5.0x System In this scenario, you are installing SCO UNIX OpenDesktop 3.x or OpenServer 5.0x on a single drive or array group. To install the driver 1 Start up the system with the SCO UNIX boot disk. 2 For OpenServer 5.0x, at the boot prompt type defbootstr ahslink=dpti5 For OpenServer 5.04 or later, at the boot prompt type defbootstr link=dpti5 3 When prompted for the SCO BTLD disk, insert the driver disk you created earlier (refer to page 3-26). 4 Insert the N1 or Boot Disk again when prompted. 5 Insert the N2 disk when prompted. During the Hardware Roster, the following line should appear: % adapter type=dpti ha=0 id=7 channel=0, PCI 6 Continue the installation according to the SCO documentation. Note: If you are installing from tape or CD, OpenServer 5.x locates the tape or CD automatically. Adding the Controller to an Existing OpenDesktop 3.x or OpenServer 5.x System In this scenario, you are adding an Adaptec RAID controller to an existing Open Desktop 3.x or OpenServer 5.x system. To install the driver 1 Install and configure your Adaptec RAID controller and hard drives according to the instructions in Chapter 2. 2 Boot SCO UNIX. 3 After SCO UNIX has booted, insert the driver disk you created earlier (refer to page 3-26). 3-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
3-27
Installing the Driver
Installing the Driver in a New OpenServer 5.0x System
In this scenario, you are installing SCO UNIX OpenDesktop 3.
x
or
OpenServer 5.0
x
on a single drive or array group. To install the
driver
1
Start up the system with the SCO UNIX boot disk.
2
For OpenServer 5.0
x
, at the boot prompt type
defbootstr
ahslink=dpti5
For OpenServer 5.04 or later, at the boot prompt type
defbootstr link=dpti5
3
When prompted for the SCO BTLD disk, insert the driver disk
you created earlier (refer to
page 3-26
).
4
Insert the N1 or Boot Disk again when prompted.
5
Insert the N2 disk when prompted. During the Hardware
Roster, the following line should appear:
% adapter type=dpti ha=0 id=7 channel=0, PCI
6
Continue the installation according to the SCO documentation.
Note:
If you are installing from tape or CD, OpenServer 5.
x
locates the tape or CD automatically.
Adding the Controller to an Existing OpenDesktop 3.x or
OpenServer 5.x System
In this scenario, you are adding an Adaptec RAID controller to an
existing Open Desktop 3.
x
or OpenServer 5.
x
system. To install the
driver
1
Install and configure your Adaptec RAID controller and hard
drives according to the instructions in
Chapter 2
.
2
Boot SCO UNIX.
3
After SCO UNIX has booted, insert the driver disk you created
earlier (refer to
page 3-26
).