Adaptec FC2101CDR2-AC Installation Guide - Page 8

8

Mechanical Loading

........................................................................

31

Electrical Considerations

.........................................................................

32

Circuit Overloading

.........................................................................

32

Setting Fibre Channel Loop Speed (2Gb or 1Gb)

...................................

32

2Gb Operation

.................................................................................

32

1Gb Operation

.................................................................................

33

Split Fibre Channel Loop Operation (Quad Loop)

..................................

34

Setting Up Split Loop Operation

.....................................................

34

Removing Split Loop Operation

.....................................................

34

Configuration Rules

.................................................................................

35

Supported Host Bus Adapters

..................................................................

35

Supported Cables

.....................................................................................

36

Copper Cables

.................................................................................

36

Optical Cables

.................................................................................

36

Chapter 3: JBOD Configurations

.....................................

37

Setting the Enclosure ID

..........................................................................

37

Configurations

.........................................................................................

40

JBOD Configurations

..............................................................................

41

Dual FC Loop Configuration

...........................................................

41

Quad Loop Configuration

................................................................

44

Connecting a Power Source

.....................................................................

45

Connecting an AC Power Source

....................................................

45

Disk Drive Spin Up Sequence

.................................................................

46

Chapter 4: RAID Configurations

......................................

47

2Gb SANbloc Series RAID Controller Introduction

...............................

47

RAID Controller Circuit Boards

..............................................................

49

Section	Page
Disclaimer and Warranty	3
Disclaimer	3
Warranty	3
Table of Contents	7
Preface	13
Audience	13
Conventions Used In This User Guide	13
Getting Support	14
FCC Statement	14
VCCI	15
European Community Statement	15
Safety Statements	16
Chapter 1: Introduction	19
Introduction	19
Features	19
Disk Drive Carrier	20
Power Supplies	20
Cooling System	21
I/O Option Modules	22
Chapter 2: Installation and Setup	27
Safety Statements	28
Unpacking and Initial Setup	30
Installing the System in an Equipment Rack	30
Ambient Temperature	30
Air Flow	31
Mechanical Loading	31
Electrical Considerations	32
Circuit Overloading	32
Setting Fibre Channel Loop Speed (2Gb or 1Gb)	32
2Gb Operation	32
1Gb Operation	33
Split Fibre Channel Loop Operation (Quad Loop)	34
Setting Up Split Loop Operation	34
Removing Split Loop Operation	34
Configuration Rules	35
Supported Host Bus Adapters	35
Supported Cables	36
Copper Cables	36
Optical Cables	36
Chapter 3: JBOD Configurations	37
Setting the Enclosure ID	37
Configurations	40
JBOD Configurations	41
Dual FC Loop Configuration	41
Quad Loop Configuration	44
Connecting a Power Source	45
Connecting an AC Power Source	45
Disk Drive Spin Up Sequence	46
Chapter 4: RAID Configurations	47
2Gb SANbloc Series RAID Controller Introduction	47
RAID Controller Circuit Boards	49
Controller Circuit Board	49
I/O Circuit Board	50
Ethernet Circuit Board	50
RAID Controller Location	51
RAID Controller Status LEDs	52
RAID Controller Configurations	53
Setting the Enclosure ID	53
Configurations	55
Single RAID Controller Configuration	56
Dual RAID Controller Configuration	59
Connecting a Power Source	62
Connecting an AC Power Source	62
Disk Drive Spin Up Sequence	63
Chapter 5: System Monitoring	65
Overview	65
LS Module	65
LS Module Features	66
2Gb SANbloc Enclosure LEDs	66
Disk Drive LEDs	69
Power Supply LEDs	71
Advanced Cooling Module (ACM) LEDs	72
RAID Controller LEDs	73
Chapter 6: Installing and Removing Components	75
Location of the Components	76
Installing and Removing a Disk Drive Carrier	77
Installing a Disk Drive Carrier	77
Removing a Disk Drive Carrier	77
Installing and Removing an LS Module	79
Installing an LS Module	79
Removing an LS Module	79
Installing and Removing a Power Supply	81
Installing a Power Supply	81
Removing a Power Supply	81
Installing and Removing an Advanced Cooling Module	82
Installing an Advanced Cooling Module	82
Removing an Advanced Cooling Module	82
Installing and Removing an I/O Module/RAID Controller	83
Installing an I/O Module/RAID Controller	83
Removing an I/O Module/RAID Controller	83
Appendix A: Safety Statement Translations	85
Appendix B: Technical Specifications	95
Host Interface	95
Disk Drive Interface	95
System	95
Redundant, Hot Swappable Components	95
Physical Dimensions	96
Deskside Enclosure	96
Rack Enclosure	96
Warranty	96
Monitoring	96
Failure Notification	96
Disk Drives	97
Power Supply	97
AC Power Supply Input	97
Temperature	97
Humidity	97
Altitude	98
Operational Shock	98
Operational Vibration	98
Regulatory Agency Compliance	99
Product Safety Standards	99
Product Safety Third Party Certifications	99
CE Mark	99
Electromagnetic Radiation	99
Appendix C: Configuration Loop Diagrams	101
Appendix D: Upgrading a 2Gb SANbloc JBOD Array to a RAID Array	105
Equipment and parts necessary for upgrade	105
Upgrading from JBOD to RAID	105

Adaptec FC2101CDR2-AC Installation Guide - Page 8

JBOD Configurations, Setting Fibre Channel Loop Speed 2Gb or 1Gb - acs

Page 8 highlights