Alpine NVD-W912 All Rights Reserved. |

Alpine NVD-W912 Manual

Get Alpine NVD-W912 PDF manuals and user guides View all Alpine NVD-W912 manuals
Add to My Manuals
Save this manual to your list of manuals

Alpine NVD-W912 manual content summary:

  • Alpine NVD-W912 | All Rights Reserved. | - Page 1
    QuiCk REFERENCE GuidE in-daSH gpS naVigaTion receiVer Map update applies to following products: NVd-w912 for iNA-w910 and iVA-NAV-20 NVd-w902 for iNA-w900, iNA-w900BT and iVA-NAV-10 ina-W900, ina-W900bT & iVa-naV-10 do not have the Traffic feature
  • Alpine NVD-W912 | All Rights Reserved. | - Page 2
    TABLE OF CONTENTS SYSTEM CONTROLS 2 Lane Guidance 3 Junction View 3 Entering an address 4 Select an intersection as the destination 7 Quick search for a Place of Interest......... 10 Editing the list of destinations 12 Cancel the active route 13 Saving a location as an Address Book entry 14
  • Alpine NVD-W912 | All Rights Reserved. | - Page 3
    SYSTEM CONTROLS 2
  • Alpine NVD-W912 | All Rights Reserved. | - Page 4
    Lane Guidance When navigating, these arrows represent the lanes to take. Junction View When navigating, highlighted signs represent which lanes to use; all others are dimmed. 3
  • Alpine NVD-W912 | All Rights Reserved. | - Page 5
    Entering an address To enter an address as the destination, do as follows: 1. Press the [NAVI MENU], then tap 2. Tap 3.By default, the software proposes the state where you are driving. If needed, tap , enter a few letters of the destination state on the keyboard, and select one from the
  • Alpine NVD-W912 | All Rights Reserved. | - Page 6
    Entering an address c. Find the city you need: • The most likely city name is always shown in the input field. To accept it, tap . • If the desired name does not appear, a list a names will open representing the names that are the closest match to the characters you have entered. To open this list
  • Alpine NVD-W912 | All Rights Reserved. | - Page 7
    Entering an address 6.Enter the house number: a. Enter the house number on the keyboard. (To enter symbols, tap ). b. Tap to finish entering the address. (if the entered house number cannot be found, the midpoint of the street is selected as the destination.) 7. A full screen map appears with
  • Alpine NVD-W912 | All Rights Reserved. | - Page 8
    Select an intersection as the destination To enter an intersection of two streets as the destination, do as follows: 1. Press the [NAVI MENU] hard key, then tap 2. Tap . 3.By default, the software proposes the state where you are. If needed, tap , enter a few letters of the destination state on the
  • Alpine NVD-W912 | All Rights Reserved. | - Page 9
    Select an intersection as the destination c. Find the city you need: • The most likely city name is always shown in the input field. To accept it, tap . • If the desired name does not appear, a list a names will open representing the names that are the closest match to the characters you have
  • Alpine NVD-W912 | All Rights Reserved. | - Page 10
    Select an intersection as the destination 6. Instead of entering the house number, tap . The system will prompt you to enter the intersecting street name. 7. A full screen map appears with the selected point in the middle. If necessary, tap the map somewhere else to modify the destination. The
  • Alpine NVD-W912 | All Rights Reserved. | - Page 11
    Quick search for a Place of Interest The Quick search feature lets you quickly find a Place by its name. The search is always carried out • along the recommended route if it exists or • around your current location if there is no destination given. 1. To start the Quick search function, press the [
  • Alpine NVD-W912 | All Rights Reserved. | - Page 12
    Quick search for a Place of Interest 4.After entering a few letters, tap to open the list of Places with names closely matching what you have already entered. 5.Browse the list if necessary and tap one of the list items. A full screen map appears with the selected point in the middle. The
  • Alpine NVD-W912 | All Rights Reserved. | - Page 13
    add a new destination. • Tap to delete a destination. • Tap to modify the start point of the route. • Tap to reorder the list. You can do it manually or you can let the application optimize the route for you. 12
  • Alpine NVD-W912 | All Rights Reserved. | - Page 14
    Cancel the active route To cancel the calculated route, press the [NAVI MENU] hard key, tap in the Navigation menu, and then tap . The active route is deleted with all its waypoints once you press on the screen. 13
  • Alpine NVD-W912 | All Rights Reserved. | - Page 15
    Saving a location as an Address Book entry 1. Select a destination as described previously. It can be an address, a Place, and any location on the map, a previously used destination from History, a coordinate or a location where a photo was taken. 2. When the full screen map appears with the
  • Alpine NVD-W912 | All Rights Reserved. | - Page 16
    Speed limit warning Maps may contain information about the speed limits of the road segments. The software can warn you if you exceed the current limit while driving these segments. This information may not be available for your region (ask your local dealer), or may not be correct for all roads on
  • Alpine NVD-W912 | All Rights Reserved. | - Page 17
    Adjusting Speed Warning 1. Press [Navi Menu] Hard Key 2. Select [Settings] 3. Select [Sounds and Warnings] 4.Select [Speed Warning Settings] 5. Use the slider to adjust when the warning is triggered (130% would warn the least) 16
  • Alpine NVD-W912 | All Rights Reserved. | - Page 18
    the most up-todate traffic conditions. To fine-tune this recalculation, you can set the minimum delay that can trigger a route recalculation. You can also instruct the software to have you confirm the new recommended route before it takes effect. You can do these in Traffic settings. *W900 does not
  • Alpine NVD-W912 | All Rights Reserved. | - Page 19
    Traffic Settings / Understanding traffic* A special icon ( ) is displayed on the Map screen to show you whether traffic events are received. The icon shows the status of the traffic receiver when there are no traffic events on your route, otherwise it shows the type of the next traffic
  • Alpine NVD-W912 | All Rights Reserved. | - Page 20
    Traffic events Road segments affected by traffic events are displayed with an alternate color on the map. Small symbols above the road show the nature of the event. Tap to open the list of traffic event categories: In the first column you can see the number of traffic events on your route. The
  • Alpine NVD-W912 | All Rights Reserved. | - Page 21
    To enable/disable Traffic features 1. Press [Navi Menu] Hard Key 2. Select [Settings] 3. Select [Traffic] 4.Selecting [Smart Routes] will use traffic information in routing. Selecting [Traffic Receiver] will turn the traffic feature off completely (uncheck this box to disable "traffic ahead" verbal
  • Alpine NVD-W912 | All Rights Reserved. | - Page 22
    Quick Menu Any screen that the symbol is available, press it and it will take you to a 'quick menu' where you can search for a POI, or DELETE a route. 21
  • Alpine NVD-W912 | All Rights Reserved. | - Page 23
    Route Settings 1. Press [Navi Menu] key 2. Select [Settings] 3. Select [Route Setting] 4. Then choose the options you want (Use Highways, Toll roads, Carpool Lanes, or unpaved roads) in route calculations 22
  • Alpine NVD-W912 | All Rights Reserved. | - Page 24
    Route Settings Selected map location (Cursor) and selected map object You can mark a map location in the following ways: • Tap the map when navigating, • Tap the map when you are asked to confirm the destination at the end of a search, or • Tap the map in Find on Map When a map location is selected
  • Alpine NVD-W912 | All Rights Reserved. | - Page 25
    SCROLLING the map Tap the map anywhere to browse it during navigation. The map stops following the current position (the Vehimarker, a blue arrow by default, is not locked in a fixed position on the screen any more) and control buttons appear to help you modify the map view. Action Moving the map
  • Alpine NVD-W912 | All Rights Reserved. | - Page 26
    SCROLLING the map Action Rotating left and right Button Compass , , Info Return to normal navigation Additional options Select destination Description Changes the horizontal view angle of the map. Tap the button once to modify the view in large steps, or tap and hold the button to modify it
  • Alpine NVD-W912 | All Rights Reserved. | - Page 27
    Changing the language 1. Press [Navi Menu] Hard Key 2. Select [Settings] 3. Select [Clock/Regional] 4. Select [Menu Language] 26
  • Alpine NVD-W912 | All Rights Reserved. | - Page 28
    Changing the language 5. Select Desired Language 6. Then the system will prompt you to restart, TAP [RESTART] 27
  • Alpine NVD-W912 | All Rights Reserved. | - Page 29
    trigger the VOICE to repeat, press the MAP hardkey Setting Home Follow Step 1,2, 3 under Saving a location as an Address Book entry in Quick Reference Guide. Use the keyboard to change the name for the Address Book entry to 'Home.' Tap Done to save the Home location. Curves/Corners ahead Press
  • Alpine NVD-W912 | All Rights Reserved. | - Page 30
    What's new? Make a phone call to place of interest 1. Connect your phone to W910 via Bluetooth 2. Follow Step 1,2,3,4,5 under Quick search for a Place of Interest in Quick Reference Guide. 3. Tap 4. Tap to call 29
  • Alpine NVD-W912 | All Rights Reserved. | - Page 31
    . 8. Q: H ow can I stop the system from providing speed warnings verbally? A: Please see page (15?) of the Quick Users Guide. 9. Q: A certain address cannot be found in the system, and the area has been there for over 6 months. A: Due to compilation and production time, newer addresses
  • Alpine NVD-W912 | All Rights Reserved. | - Page 32
    FAQ 10.Q: How do I customize my VP marker? (blue triangle) A: Navi Menu -> Settings -> Scroll Down->Map Settings -> Scroll Down ->Select 3D Vehicle Gallery-> Use the arrows to select your icon. 31
  • Alpine NVD-W912 | All Rights Reserved. | - Page 33
    ALPINE IN-DASH NAVIGATION QUICK REFERENCE GUIDE P/N: NVD-W912 & NVD-W902
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
QUICK REFERENCE GUIDE
IN-DASH GPS NAVIGATION RECEIVER
Map Update applies to following products:
NVD-W912 for INA-W910 and IVA-NAV-20
NVD-W902 for INA-W900, INA-W900BT and
IVA-NAV-10
INA-W900, INA-W900BT & IVA-NAV-10 do not have the Traffic Feature