Alpine PXA-H800 User Manual - Page 23

Turning RoadEQ On/Off

Get Alpine PXA-H800 PDF manuals and user guides View all Alpine PXA-H800 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

5 Click [Setup] for "RoadEQ." 6 When a confirmation message is displayed, check the content and click [OK]. 7 Click [START] in the measurement start screen. Countdown will start. From a PC Turning RoadEQ On/Off When automatic measurement is completed, RoadEQ can be turned on or off and its level can be selected. 1 Click [RoadEQ] for [Shortcut] tab in the main menu. The Automatic Measurement tab screen will be displayed. • When you click [Automatic Measurement] in the Function switching tab, the Automatic Measurement tab screen will also be displayed. Refer to "Operating the Function Switching Tab" (page 7). 2 Click [ON] or [OFF] for "RoadEQ." When you click [ON], select the level. • When you do not use RoadEQ, select [OFF]. 3 Click [ ] and select and click either [Level 1], [Level 2], or [Level 3]. During the 10 second countdown, go outside the vehicle and close the door. A test signal will be output from the speakers to measure the acoustic characteristics of the cabin. Do not open any doors until the finish message appears on the screen. If external noise interferes with the measurement. If the error screen is displayed, perform the measurement again. • If you want to stop measurement, click [CANCEL]. • If no microphone is connected, a confirmation message will be displayed and measurement will not be carried out. Click [OK] to cancel the indication. 8 When a confirmation message for closing the screen is displayed, click [OK]. • To enable this function, Defeat should be is set to ON. • Measurement of RoadEQ takes approximately 7 minutes. • Measurement values will not be lost in the event the system is reset or battery power is disconnected. Level 1: Low correction level. Suitable for quiet vehicles. Level 2: Moderate correction level. Level 3: High correction level. Suitable for high speed driving. • If measurement is not completed, or a microphone is not connected, this setting cannot be performed. • When you change the speaker setting of On/Off, RoadEQ automatically becomes off. When you have changed the speaker settings, start the measurement step over again. • After the setting, it is recommended to store the setting contents on the unit. For details, refer to "Storing the Preset Values (Preset Store)" (page 12). 21-EN

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
21
-EN
From a PC
5
Click [Setup] for “RoadEQ.”
6
When a confirmation message is displayed, check
the content and click [OK].
7
Click [START] in the measurement start screen.
Countdown will start.
During the 10 second countdown, go outside the vehicle
and close the door.
A test signal will be output from the speakers to measure the
acoustic characteristics of the cabin. Do not open any
doors until the finish message appears on the screen. If
external noise interferes with the measurement. If the error
screen is displayed, perform the measurement again.
•
If you want to stop measurement, click [CANCEL].
•
If no microphone is connected, a confirmation message will be
displayed and measurement will not be carried out. Click [OK] to
cancel the indication.
8
When a confirmation message for closing the screen
is displayed, click [OK].
•
To enable this function, Defeat should be is set to ON.
•
Measurement of RoadEQ takes approximately 7 minutes.
•
Measurement values will not be lost in the event the system is reset or
battery power is disconnected.
When automatic measurement is completed, RoadEQ can be turned on
or off and its level can be selected.
1
Click [RoadEQ] for [Shortcut] tab in the main menu.
The Automatic Measurement tab screen will be displayed.
•
When you click [Automatic Measurement] in the Function switching
tab, the Automatic Measurement tab screen will also be displayed.
Refer to “Operating the Function Switching Tab” (page 7).
2
Click [ON] or [OFF] for “RoadEQ.”
When you click [ON], select the level.
•
When you do not use RoadEQ, select [OFF].
3
Click [
] and select and click either [Level 1], [Level
2], or [Level 3].
Level 1:
Low correction level. Suitable for quiet vehicles.
Level 2:
Moderate correction level.
Level 3:
High correction level. Suitable for high speed
driving.
•
If measurement is not completed, or a microphone is not connected,
this setting cannot be performed.
•
When you change the speaker setting of On/Off, RoadEQ
automatically becomes off. When you have changed the speaker
settings, start the measurement step over again.
•
After the setting, it is recommended to store the setting contents on
the unit. For details, refer to “Storing the Preset Values (Preset
Store)” (page 12).
Turning RoadEQ On/Off