Asus CUSL2 CUSL2 User Manual - Page 24

System Memory DIMM - max cpu

Get Asus CUSL2 PDF manuals and user guides View all Asus CUSL2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

3. HARDWARE SETUP 3.5 System Memory (DIMM) NOTE: No hardware or BIOS setup is required after adding or removing memory. This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are available for 3.3Volt (power level) unbuffered Synchronous Dynamic Random Access Memory (SDRAM). One side (with memory chips) of the DIMM takes up one row on the motherboard. Memory speed setup is recommended through SDRAM Configuration in 4.4.1 Chip Configuration. Install memory in any combination as follows: DIMM Location 168-pin DIMM Total Memory Socket 1 (Rows 0&1) SDRAM 8, 16, 32, 64, 128, 256, 512MB x1 Socket 2 (Rows 2&3) SDRAM 8, 16, 32, 64, 128, 256, 512MB x1 Socket 3 (Rows 4&5) SDRAM 8, 16, 32, 64, 128, 256, 512MB x1 Total System Memory (Max 512MB) = NOTE: Make sure the total installed memory does not exceeds 512MB. Otherwise, the system may hang during startup. 3.5.1 General DIMM Notes • ASUS motherboards support SPD (Serial Presence Detect) DIMMs. This is the memory of choice for best performance vs. stability. • BIOS shows SDRAM memory on bootup screen. • Single-sided DIMMs come in 16, 32, 64,128, 256MB; double-sided come in 32, 64, 128, 256, 512MB. NOTE: For PC133 SDRAM to run at 133MHz, the system CPU bus must also operate at that speed. 3. H/W SETUP System Memory 24 ASUS CUSL2 User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
ASUS CUSL2 User’s Manual
3. HARDWARE SETUP
24
System Memory
3. H/W SETUP
3.5
System Memory (DIMM)
NOTE:
No hardware or BIOS setup is required after adding or removing memory.
This motherboard uses only Dual Inline Memory Modules (DIMMs). Sockets are
available for
3.3Volt
(power level) unbuffered Synchronous Dynamic Random Ac-
cess Memory (SDRAM). One side (with memory chips) of the DIMM takes up one
row on the motherboard.
Memory speed setup is recommended through
SDRAM Configuration
in
4.4.1
Chip Configuration.
NOTE:
Make sure the total installed memory does not exceeds 512MB. Otherwise,
the system may hang during startup.
3.5.1
General DIMM Notes
•
ASUS motherboards support SPD (Serial Presence Detect) DIMMs. This is the
memory of choice for best performance vs. stability.
•
BIOS shows SDRAM memory on bootup screen.
•
Single-sided DIMMs come in 16, 32, 64,128, 256MB; double-sided come in 32,
64, 128, 256, 512MB.
NOTE:
For PC133 SDRAM to run at 133MHz, the system CPU bus must also
operate at that speed.
Install memory in any combination as follows:
DIMM Location
168-pin DIMM
Total Memory
Socket 1 (Rows 0&1)
SDRAM 8, 16, 32, 64, 128, 256, 512MB
x1
Socket 2 (Rows 2&3)
SDRAM 8, 16, 32, 64, 128, 256, 512MB
x1
Socket 3 (Rows 4&5)
SDRAM 8, 16, 32, 64, 128, 256, 512MB
x1
Total System Memory (Max 512MB)
=