Asus M4A78-E SE User Manual - Page 94
UsÒr AccÒss LÒvÒÓ [FuÓÓ AccÒss]
View all Asus M4A78-E SE manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 94 highlights
BIOS SETUP UTILITY Boot Security Settings Supervisor Password User Password : Installed : Installed Change Supervisor Password User Access Level Change User Password Clear User Password Password Check [Full Access] [Setup] to change password. again to disabled password. User Access Level [Full Access] BIOS [No Access BIOS 程序。 [View Only BIOS [Limited] BIOS [Full Access BIOS 程序。 Change User Password Not Installed Installed。 User Password): 1. 選擇 Change User Password Enter>。 2. 在 Enter Password Enter>。 3 Confirm Password Password Installed Password do not match User Password Installed。 Clear User Password Password Check [Setup] [Setup] B I O S B I O S [Always] BIOS 第三章 3-32 BIOS
3-32
第三»:BIOS 程序¿À
程序¿À
第三»
UsÒr AccÒss LÒvÒÓ [FuÓÓ AccÒss]
本項目可讓您選擇 BIOS 程序存取限制權限等級
[No AccÒss]
用戶Ê法存取 BIOS 程序。
[ViÒÑ OnÓy]
允許用戶讀取 BIOS 程序但Ê法更改任何項目。
[LimitÒd]
允許用戶僅能存取 BIOS 程序的某些項目。例如:系統時間。
[FuÓÓ AccÒss]
允許用戶存取´µ的 BIOS 程序。
ChangÒ UsÒr PassÑord(更改用戶密碼)
本項目是用於更改用戶密碼,運行狀態會於畫面上方以淡灰色顯示,默認值為 Not
InstaÓÓÒd。Á您¿À密碼後,則此項目會顯示 InstaÓÓÒd。
¿À用戶密碼(UsÒr PassÑord):
1.
選擇 ChangÒ UsÒr PassÑord 項目並按下 <EntÒr>。
2. 在 EntÒr PassÑord 窗口出現時,請輸入欲¿À的密碼,可以是六個字節內的英
文、數字與ÎÆ。輸入´成按下 <EntÒr>。
3. 接著會再出現 Confirm PassÑord 窗口,再一次輸入密碼以確認密碼正確。密碼
確認Ê誤時,系統會出現 PassÑord InstaÓÓÒd 信息,代表密碼¿À´成。若出現
PassÑord do not match! 信息,代表於密碼確認時輸入錯誤,請重新輸入一
次。此時畫面上方的 UsÒr PassÑord 項目會顯示 InstaÓÓÒd。
若要更改用戶的密碼,請依照上述程序再運行一次密碼¿À。
CÓÒar UsÒr PassÑord(清除用戶密碼)
請選擇本項目來清除用戶密碼。
PassÑord ChÒck [SÒtup]
[SÒtup]
BIOS 程序會於用戶進入 BIOS 程序¿À畫面時,要求輸入用戶密
碼。
[AÓÑays]
BIOS 程序會在啟動過程要用戶輸入密碼。
Security Settings
Supervisor Password
: Installed
User Password
: Installed
Change Supervisor Password
User Access Level
[Full Access]
Change User Password
Clear User Password
Password Check
[Setup]
BIOS SETUP UTILITY
Boot
<Enter> to change
password.
<Enter> again to
disabled password.