Asus P2B-D2 P2B-D2 User Manual - Page 89

E. BusMaster

Get Asus P2B-D2 PDF manuals and user guides View all Asus P2B-D2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

WINDOWS NT 4.0 E. BusMaster WINDOWS NT 4.0 E. BusMaster This subsection describes how to install the software on a system where Windows NT Version 4.0 is installed. NOTE: This procedure assumes that the driver (PIIXIDE.SYS), installation file (OEMSETUP.INF) and tag file (DISK1.NT) are located in the same directory. Record the locations of the driver installation and Windows NT directories before installing the driver. If the driver is installed on the system, un-install the driver (following the directions in the "Un-installing the Software" section) PRIOR to re-installing the driver. 1. Check the System Requirements. Windows NT must be fully installed and running on the system prior to installing the driver. 2. Close any running applications. 3. Select My Computer. 4. Open the Control Panel Folder. 5. Invoke the SCSI Adapters applet. 6. Click the Drivers tab. The currently installed SCSI adapter drivers will be listed in the Drivers menu. The display MAY list the default driver, "IDE CD-ROM (Atapi 1.2) / Dual-Channel PCI IDE Controller" OR a previously installed PIIX Bus Master IDE driver, "Intel PIIX PCI Bus Master IDE Controller". NOTE: this text may vary according to the release of Windows NT*. If NONE of these adapter drivers are listed, go to step 9. 7. If the "Intel PIIX PCI Bus Master IDE Controller" driver is listed, select it. Then, select Remove to remove the driver. 8. If the default driver "IDE CD-ROM (Atapi 1.2) / Dual-Channel PCI IDE" is listed, select it. Then, select Remove to remove the driver. 9. Select Add to add a new driver. 10. From the Install Disk window, select Have Disk. 11. The Windows NT Setup dialog box will appear prompting for the path of the installation files. Specify the location of the driver installation directory when prompted to do so. NOTE: This procedure assumes that the driver (PIIXIDE.SYS), installation file (OEMSETUP.INF) and tag file (DISK1.NT) are located in the same directory. 12. Click Intel PIIX PCI Bus Master IDE Controller and then click OK. NOTE: If the driver was previously installed on the system, a dialog box will appear that states that driver for the "Intel PIIX PCI Bus Master IDE Controller" is already on the system. If this occurs, select New to install the new driver. 13. When prompted, reboot the system as directed in order for the changes to take effect. ASUS P2B-D2 User's Manual 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
ASUS P2B-D2 User’s Manual
89
E. BusMaster
This subsection describes how to install the software on a system where Windows
NT Version 4.0 is installed.
NOTE:
This procedure assumes that the driver (PIIXIDE.SYS), installation file
(OEMSETUP.INF) and tag file (DISK1.NT) are located in the same directory. Record
the locations of the driver installation and Windows NT directories before installing
the driver. If the driver is installed on the system, un-install the driver (following the
directions in the "Un-installing the Software" section) PRIOR to re-installing the driver.
1.
Check the System Requirements.
Windows NT must be fully installed and run-
ning on the system prior to installing the driver.
2.
Close any running applications.
3.
Select
My Computer
.
4.
Open the
Control Panel
Folder.
5.
Invoke the
SCSI Adapters
applet.
6.
Click the
Drivers
tab. The currently installed SCSI adapter drivers will be listed
in the Drivers menu. The display MAY list the default driver, "IDE CD-ROM
(Atapi 1.2) / Dual-Channel PCI IDE Controller" OR a previously installed PIIX
Bus Master IDE driver, "Intel PIIX PCI Bus Master IDE Controller".
NOTE:
this text may vary according to the release of Windows NT*. If NONE of these
adapter drivers are listed, go to step 9.
7.
If the "Intel PIIX PCI Bus Master IDE Controller" driver is listed, select it.
Then, select
Remove
to remove the driver.
8.
If the default driver "IDE CD-ROM (Atapi 1.2) / Dual-Channel PCI IDE" is
listed, select it.
Then, select
Remove
to remove the driver.
9.
Select
Add
to add a new driver.
10. From the
Install Disk
window, select
Have Disk
.
11. The
Windows NT Setup
dialog box will appear prompting for the path of the
installation files. Specify the location of the driver installation directory when
prompted to do so.
NOTE:
This procedure assumes that the driver (PIIXIDE.SYS), installation file
(OEMSETUP.INF) and tag file (DISK1.NT) are located in the same directory.
12. Click
Intel PIIX PCI Bus Master IDE Controller
and then click
OK
.
NOTE:
If the driver was previously installed on the system, a dialog box will
appear that states that driver for the "Intel PIIX PCI Bus Master IDE Controller"
is already on the system. If this occurs, select
New
to install the new driver.
13. When prompted, reboot the system as directed in order for the changes to take
effect.
WINDOWS NT 4.0
WINDOWS NT 4.0
E.
BusMaster