Asus SP98AGP-X SP98AGP-X User Manual - Page 33

Power Connection Procedures

Get Asus SP98AGP-X PDF manuals and user guides View all Asus SP98AGP-X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

III. INSTALLATION Power Connections III. INSTALLATION Power Connection Procedures 1. After all jumpers and connections are made, close the system case cover. 2. Be sure that all switches are off (in some systems, marked with ). 3. Connect the power supply cord into the power supply located on the back of your system case according to your system user's manual. 4. Connect the power cord into a power outlet that is equipped with a surge protector. 5. You may then turn on your devices in the following order: a. Your monitor b. External SCSI devices (starting with the last device on the chain) c. Your system power. For ATX power supplies, you need to switch on the power supply as well as press the ATX power switch on the front of the case. 6. The power LED on the front panel of the system case will light. For ATX power supplies, the system LED will light when the ATX power switch is pressed. The monitor LED may light up after the system's if it complies with "green" standards or if it has a power standby feature. The system will then run power-on tests. While the tests are running, additional messages will appear on the screen. If you do not see anything within 30 seconds from the time you turn on the power, the system may have failed a power-on test. Recheck your jumper settings and connections or call your retailer for assistance. 7. During power-on, hold down to enter BIOS setup. Follow the instructions in the next section, BIOS SOFTWARE. * Powering Off your computer: You must first exit or shut down your operating system before switching off the power switch. For ATX power supplies, you can press the ATX power switch after exiting or shutting down your operating system. If you use Windows 95, click the Start button, click Shut Down, and then click Shut down the computer?. The system will give three quick beeps after about 30 seconds and then power off after Windows shuts down. NOTE: The message "You can now safely turn off your computer" will not appear when shutting down with ATX power supplies. ASUS SP98AGP-X User's Manual 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
ASUS SP98AGP-X User’s Manual
33
III. INSTALLATION
Power Connections
III.
INSTALLATION
Power Connection Procedures
1.
After all jumpers and connections are made, close the system case cover.
2.
Be sure that all switches are off (in some systems, marked with
).
3.
Connect the power supply cord into the power supply located on the back of
your system case according to your system user’s manual.
4.
Connect the power cord into a power outlet that is equipped with a surge protector.
5.
You may then turn on your devices in the following order:
a.
Your monitor
b.
External SCSI devices (starting with the last device on the chain)
c.
Your system power. For ATX power supplies, you need to switch
on the power supply as well as press the ATX power switch on the
front of the case.
6.
The power LED on the front panel of the system case will light.
For ATX power
supplies, the system LED will light when the ATX power switch is pressed.
The
monitor LED may light up after the system’s if it complies with “green” stan-
dards or if it has a power standby feature.
The system will then run power-on
tests.
While the tests are running, additional messages will appear on the screen.
If you do not see anything within 30 seconds from the time you turn on the
power, the system may have failed a power-on test.
Recheck your jumper set-
tings and connections or call your retailer for assistance.
7.
During power-on, hold down <Delete> to enter BIOS setup.
Follow the instruc-
tions in the next section, BIOS SOFTWARE.
*
Powering Off your computer:
You must first exit or shut down your operating
system before switching off the power switch.
For ATX power supplies, you
can press the ATX power switch after exiting or shutting down your operating
system.
If you use Windows 95, click the
Start
button, click
Shut Down
, and
then click
Shut down the computer?
. The system will give three quick beeps
after about 30 seconds and then power off after Windows shuts down.
NOTE:
The message “You can now safely turn off your computer” will not
appear when shutting down with ATX power supplies.