Asus V3-P5945GC User Manual - Page 36

Connect the blue interface of the IDE ribbon cable to the IDE

Get Asus V3-P5945GC - V Series - 0 MB RAM PDF manuals and user guides
UPC - 610839942145
View all Asus V3-P5945GC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

4. Connect a 5-pin Serial ATA power plug from the power supply unit to the 5-pin power connector at the back of the drive. - OR - Connect a 4-pin (female) power plug from the power supply unit to the 4-pin (male) power connector at the back of the drive. Serial ATA power cable Serial ATA cable If your Serial ATA HDD has both 4-pin and 5-pin connectors at the back, use either the 5-pin SATA power adapter plug OR the legacy 4‑pin power connector. DO NOT use both to prevent damage to components and to keep the system from becoming unstable. To install an IDE hard disk drive: 1. Follow steps 1-2 of the previous section. 2. Connect the blue interface of the IDE ribbon cable to the IDE connector on the motherboard. IDE ribbon cable Power cable 2-18 Chapter 2: Basic installation

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
2-18
Chapter 2: Basic installation
To install an IDE hard disk drive:
1.
Follow steps 1-2 of the previous section.
2.
Connect the blue interface of the IDE ribbon cable to the IDE
connector on the motherboard.
IDE ribbon cable
Power cable
4.
Connect a 5-pin Serial ATA power plug from the power supply unit to
the 5-pin power connector at the back of the drive.
- OR -
Connect a 4-pin (female) power plug from the power supply unit to
the 4-pin (male) power connector at the back of the drive.
Serial ATA cable
Serial ATA power
cable
If your Serial ATA HDD has both 4-pin and 5-pin connectors at the back,
use either the 5-pin SATA power adapter plug
OR the legacy 4-pin power
connector.
DO NOT use both to prevent damage to components and to
keep the system from becoming unstable.