Asus V3-P5945GC User Manual - Page 37

Installing the card reader

Get Asus V3-P5945GC - V Series - 0 MB RAM PDF manuals and user guides
UPC - 610839942145
View all Asus V3-P5945GC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

• If you will install only one hard disk drive, make sure to configure your hard disk drive as Master device before connecting the IDE cable and power plug. Refer to the HDD documentation on how to set the drive as a Master device. • If you will install two IDE hard disk drives, configure the other device as Slave. 3. Connect the gray interface of the IDE ribbon cable to the IDE connector on the drive. 4. If you install two IDE hard disk drives, connect the black interface of the IDE ribbon cable to the IDE connector on the second (Slave) IDE hard disk drive. 5. Connect a 4-pin power plug from the power supply unit to the power connector at the back of the drive(s). 2.9 Installing the card reader An optional card reader module (see the figure below) is available with the system. If you want to install the card reader into your system, follow the steps on the next page. Note: the card reader is optional and users need to purchase separately. ASUS V-Series P5945GC 2-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
2-19
ASUS V-Series P5945GC
3.
Connect the gray interface of the IDE ribbon cable to the IDE
connector on the drive.
4.
If you install two IDE hard disk drives, connect the black interface of
the IDE ribbon cable to the IDE connector on the second (Slave) IDE
hard disk drive.
5.
Connect a 4-pin power plug from the power supply unit to the power
connector at the back of the drive(s).
•
If you will install only one hard disk drive, make sure to configure your
hard disk drive as Master device before connecting the IDE cable and
power plug. Refer to the HDD documentation on how to set the drive
as a Master device.
•
If you will install two IDE hard disk drives, configure the other device
as Slave.
2.9
Installing the card reader
An optional card reader module (see the figure below) is available with the
system. If you want to install the card reader into your system, follow the
steps on the next page.
Note: the card reader is optional and users need to purchase separately.