Asus X900-PIB P3C-E User Manual - Page 31

ASUS P3C-E User's Manual, ASUS P2T-Cable, IMPORTANT

Get Asus X900-PIB PDF manuals and user guides View all Asus X900-PIB manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

3. HARDWARE SETUP ASUS P2T-Cable The optional ASUS P2T-Cable can be used for a Pentium® III / II processor packaged in an SECC/SECC2 or a Celeron™ processor packaged in an SEPP . Sensor Sensor Connector Plug NOTE: The ASUS P2T-Cable can only be used in a Slot 1 motherboard with a 2-pin thermal sensor connector. To Use the ASUS P2T-Cable NOTE: The following procedures assume that you have properly attached a heatsink onto an SECC/SECC2/SEPP. 1. Simply peel off the tab from the sensor and then stick the sensor near the middle edge of the Intel boxed processor heatsink with fan (middle) or to either the upper or lower edge of the Celeron™ heatsink (right), as indicated. Tab Sensor ← OR STICK ABOUT HERE WARNING! Do not insert the sensor between the processor and heatsink, otherwise, it will cause damage to the P2T-Cable. IMPORTANT! ASUS guarantees accurate readings only for the ASUS Smart Fan and the Intel boxed processor heatsink with fan because both have similar heat distribution and heatsink material. 3. H/W SETUP CPU ASUS P3C-E User's Manual 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
ASUS P3C-E User’s Manual
31
3. HARDWARE SETUP
CPU
3. H/W SETUP
1.
Simply peel off the tab from the sensor and then stick the sensor near the middle
edge of the Intel boxed processor heatsink with fan (middle) or to either the
upper or lower edge of the Celeron™ heatsink (right), as indicated.
To Use the ASUS P2T-Cable
NOTE:
The following procedures assume that you have properly attached a
heatsink onto an SECC/SECC2/SEPP.
ASUS P2T-Cable
The optional ASUS P2T-Cable can be
used for a Pentium
®
III / II processor
packaged in an SECC/SECC2 or a
Celeron™ processor packaged in an
SEPP
.
NOTE:
The ASUS P2T-Cable can only be used in a Slot 1 motherboard with a
2-pin thermal sensor connector.
Sensor Connector Plug
Sensor
WARNING!
Do not insert the sensor between the processor and heatsink, other-
wise, it will cause damage to the P2T-Cable.
IMPORTANT!
ASUS guarantees accurate readings only for the ASUS Smart
Fan and the Intel boxed processor heatsink with fan because both have similar
heat distribution and heatsink material.
Tab
Sensor
←
OR STICK ABOUT HERE