Audiovox XDRC2V1 User Guide - Page 19

Peel off the adhesive liner°

Get Audiovox XDRC2V1 PDF manuals and user guides View all Audiovox XDRC2V1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

3 The dock mounting plate can be tilted in different directions. Adjust as necessary for your particular vehicle. When the orientation is correct, tighten the knob. Knob Adhesive Foot Dock Mounting Plate 4 Clean the surface with the alcohol preparation pad and let it dry thoroughly. 5 Peel off the adhesive liner. Position, press, and hold the Dash Mount in place for 30 seconds. IMPORTANT! Allow the Dash Mount adhesive to cure (dry) for a minimum of 2-4 hours before using the mount. The best adhesion occurs after 24 hours. TIP! To remove, carefully lift the adhesive pad with your fingers or a spoon. Warming the pad with a hair dryer for several minutes will help soften the adhesive. Be careful not overheat the surface with the hair dryer or you may damage the surface or Dash Mount. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
19
3
The dock mounting plate can be tilted in different directions°
Adjust as necessary for your particular vehicle° When the
orientation is correct, tighten the knob°
4
Clean the surface with the
alcohol preparation pad and
let it dry thoroughly°
5
Peel off the adhesive liner°
Position, press, and hold the
Dash Mount in place for 30
seconds°
IMPORTANT!
Allow the Dash Mount adhesive to cure (dry) for a minimum of
2-4 hours before using the mount° The best adhesion occurs after 24 hours°
TIP!
To remove, carefully lift the adhesive pad with your fingers or a spoon°
Warming the pad with a hair dryer for several minutes will help soften the
adhesive° Be careful not overheat the surface with the hair dryer or you may
damage the surface or Dash Mount°
Knob
Adhesive Foot
Dock Mounting Plate