Audiovox XDRC2V1 User Guide - Page 36

° Continue with Step 5: Connect the Magnetic Mount Antenna

Get Audiovox XDRC2V1 PDF manuals and user guides View all Audiovox XDRC2V1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

Vehicle Installation or controls. Secure the excess cable with wire ties (purchased separately). 4. Bring the end of the cable out at the PowerConnect Vehicle Dock location. Leave yourself enough cable so you can easily connect it to the antenna connector of the dock. 5. Continue with "Step 5: Connect the Magnetic Mount Antenna and PowerConnect Power Adapter" on page 39. • Convertible: 1. Bring the antenna cable from the antenna into the trunk at the front edge of the trunk lid. Keep any bends in the cable loose. Tape or tie the cable along the inside of the trunk lid to the trunk lid hinge strut. 2. Allow enough slack in the cable so the trunk lid can easily open and close and keep the cable away from hinges, gears, etc., that could crimp or cut it. Route the cable along the trunk wall and into the cabin through a conduit or along an existing wiring harness. 3. Route the cable through the main cabin area under the interior trim, towards the front of the vehicle. Use a blunt plastic putty knife or similar blunt tool to lift the plastic trim just enough to tuck the cable under underneath. Avoid side 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
36
Vehicle Installation
or controls° Secure the excess cable with wire ties (purchased
separately)°
4° Bring the end of the cable out at the
Power
Connect Vehicle Dock
location° Leave yourself enough cable so you can easily connect it
to the antenna connector of the dock°
5° Continue with “Step 5: Connect the Magnetic Mount Antenna and
Power
Connect Power Adapter” on page 39°
•
Convertible:
1° Bring the antenna cable from the antenna into the trunk at the front
edge of the trunk lid° Keep any bends in the cable loose° Tape or
tie the cable along the inside of the trunk lid to the trunk lid hinge
strut°
2° Allow enough slack in the cable so the trunk lid can easily open and
close and keep the cable away from hinges, gears, etc°, that could
crimp or cut it° Route the cable along the trunk wall and into the
cabin through a conduit or along
an existing wiring harness°
3° Route the cable through the
main cabin area under the
interior trim, towards the front
of the vehicle° Use a blunt
plastic putty knife or similar
blunt tool to lift the plastic trim
just enough to tuck the cable
under underneath° Avoid side