Audiovox XDRC2V1 User Guide - Page 32

Sedan/Coupe With the Antenna Placed at the Rear of the Roof

Get Audiovox XDRC2V1 PDF manuals and user guides View all Audiovox XDRC2V1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

Vehicle Installation • Sedan/Coupe With the Antenna Placed at the Rear of the Roof: 1. Feed the antenna cable from the antenna underneath the rubber molding around the rear window. Use a blunt plastic putty knife or similar blunt tool to lift the rubber molding around the rear window and tuck the antenna cable underneath the molding. Route the antenna cable around and down the window to the lowest point. If your rear window does not have rubber molding, we recommend consulting a professional installer. 2. Route the antenna cable out of the window molding and into the rubber weather stripping around the trunk opening. Lift the weather stripping from the opening and tuck the cable inside it, then replace the weather stripping. To avoid sharp bends in the cable, run the cable inside the weather stripping for a few inches, then remove the cable from the weather stripping inside the trunk. Keep the cable away from hinges, gears, etc., that could damage it. 3. Route the cable out from the rubber weather stripping and along the trunk wall. Continue routing the cable into the vehicle cabin through a conduit or along an existing wiring harness. 4. Route the cable through the main cabin area under the interior trim, towards 32

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
32
•
Sedan/Coupe With the Antenna Placed at the Rear of the Roof:
1° Feed the antenna cable from the antenna underneath the rubber
molding around the rear window° Use a blunt plastic putty knife or
similar blunt tool to lift the rubber molding around the rear window
and tuck the antenna cable underneath the molding° Route the
antenna cable around and down the window to the lowest point° If
your rear window does not have rubber molding, we recommend
consulting a professional installer°
2° Route the antenna cable out of the window molding and into the
rubber weather stripping around the trunk opening° Lift the weather
stripping from the opening and tuck the cable inside it, then replace
the weather stripping° To avoid sharp bends in the cable, run the cable
inside the weather stripping for a few inches, then remove the cable
from the weather stripping inside the trunk° Keep the cable away
from hinges, gears, etc°, that could damage it°
3° Route the cable out
from the rubber weather
stripping and along the
trunk wall° Continue routing
the cable into the vehicle
cabin through a conduit
or along an existing wiring
harness°
4° Route the cable through
the main cabin area under
the interior trim, towards
Vehicle Installation