Behringer MPA200BT Quick Start Guide - Page 6

EUROPORT MPA200BT Controls

Get Behringer MPA200BT PDF manuals and user guides View all Behringer MPA200BT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

10 EUROPORT MPA200BT EUROPORT MPA200BT Controls (1) (2) (3) (5) (4) (6) (7) (8) (9) (10) (11) (12) (13) Quick Start Guide 11 (EN) Step 2: Controls (1) LCD SCREEN displays the current DSP module and parameter settings. (2) ENCODER KNOB toggles between Graphic and Edit modes (when pressed) and changes parameter values (when rotated). (3) SETUP button steps through parameters within DSP processing modules. (4) PROCESS button steps through the DSP processing modules. (5) EXIT button returns to the top-level DSP screen when pressed. (6) ENTER button saves changes and deactivates Edit mode when pressed. (7) WIRELESS SYSTEM LEDs indicate wireless microphone signal input. (8) WIRELESS SYSTEM USB input accepts only the BEHRINGER wireless microphone receiver. NOTE: The wireless USB input works in parallel with the INPUT 1/2 analog inputs, which means the wireless microphone signal can be heard at the same time as audio coming in through the INPUT 1/2 connections. We recommend you unplug the INPUT 1/2 connections in order to hear the wireless microphone signal alone. (9) MP3 audio jack accepts audio from phone or media player using a 3.5 mm (1⁄8") plug. (10) INST/MIC IN combo jacks accept in put signals over XLR balanced, ¼" TRS balanced, or ¼" TS unbalanced connectors. (11) OUTPUT jack sends a combined signal from all inputs (INST/MIC IN jacks, wireless microphone, Bluetooth and MP3) out over a balanced XLR connection. (12) POWER switch turns the unit off and on. (13) POWER SOURCE jack accepts the included IEC cable. Charging the battery The MPA200BT ships with a rechargeable, internal battery that can power continuous audio playback for up to 20 hours. We recommend that you fully charge the battery before your first use. To charge the battery for the first time, follow this procedure: 1. Turn off the MPA200BT by pressing the POWER switch. 2. Connect the unit to an AC power outlet. The LCD screen will display to indicate the battery is charging. 3. Keep the unit plugged in to AC power until the LCD screen displays to indicate the battery has been fully charged. NOTE: The MPA200BT uses a sealed lead-acid gel battery, and the battery will slowly self-discharge when the MPA200BT is not in use. Before storing the MPA200BT for an extended period, fully charge the battery before storage, and then charge again every 3 months. NOTE: The lead-acid battery needs to be recharged every 3 months for continued operation. Please replace the battery if the MPA200BT operating timenoticeably decreases, even after a full charge cycle.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
10
EUROPORT MPA200BT
Quick Start Guide
11
EUROPORT MPA200BT Controls
(1)
(3)
(5)
(6)
(9)
(4)
(7)
(8)
(
10
)
(
12
)
(
13
)
(
11
)
(2)
(1)
LCD SCREEN
displays the current DSP module
and parameter settings.
(2)
ENCODER KNOB
toggles between Graphic
and Edit modes (when pressed) and changes
parameter values (when rotated).
(3)
SETUP
button steps through parameters
within DSP processing modules.
(4)
PROCESS
button steps through the DSP
processing modules.
(5)
EXIT
button returns to the top-level DSP
screen when pressed.
(6)
ENTER
button saves changes and deactivates
Edit mode when pressed.
(7)
WIRELESS SYSTEM LEDs
indicate wireless
microphone signal input.
(8)
WIRELESS SYSTEM USB
input accepts only
the BEHRINGER wireless microphone receiver.
NOTE:
The wireless USB input works in
parallel with the INPUT 1/2 analog inputs,
which means the wireless microphone signal
can be heard at the same time as audio
coming in through the INPUT 1/2 connections.
We recommend you unplug the INPUT 1/2
connections in order to hear the wireless
microphone signal alone.
(9)
MP3
audio jack accepts audio from phone or
media player using a 3.5 mm (±⁄8") plug.
(10)
INST/MIC IN
combo jacks accept in put signals
over XLR balanced, ¼" TRS balanced, or ¼" TS
unbalanced connectors.
(11)
OUTPUT
jack sends a combined signal
from all inputs (INST/MIC IN jacks, wireless
microphone, Bluetooth and MP3) out over a
balanced XLR connection.
(12)
POWER
switch turns the unit off
and on.
(13)
POWER SOURCE
jack accepts the
included IEC cable.
Charging the battery
The MPA200BT ships with a rechargeable, internal battery that can power continuous audio playback for up to 20 hours. We recommend that you fully charge the battery before your
first use.
To charge the battery for the first time, follow this procedure:
1.
Turn off
the MPA200BT by pressing the POWER switch.
2.
Connect the unit to an AC power outlet. The LCD screen will display
to indicate the battery is charging.
3.
Keep the unit plugged in to AC power until the LCD screen displays
to indicate the battery has been fully charged.
NOTE:
The MPA200BT uses a sealed lead-acid gel battery, and the battery will slowly self-discharge when the MPA200BT is not in use. Before storing the MPA200BT for an extended
period, fully charge the battery before storage, and then charge again every 3 months.
NOTE:
The lead-acid battery needs to be recharged every 3 months for continued operation. Please replace the battery if the MPA200BT operating timenoticeably decreases,
even after a full charge cycle.
(EN)
Step 2: Controls