Behringer NEUTRON Quick Start Guide - Page 27

52 NEUTRON Envelope 2 Controls Output Section Controls LED Sample & Hold Section Controls LED Slew Rate Limiter Section Controls Attenuator Section Controls Filter Section Controls Switches LED LFO Section Controls Switches LED Delay Section Controls Attack: 300 μs to 5 s (linear attack) Decay: 2.4 ms to 10 s (exponential decay) Sustain: 0 V to 9 V Release: 1.5 ms to 6 s (exponential release) Volume: 0 to 100% MIDI: Gate signal Rate: 0.26 Hz to 28 Hz (can be clocked from extrenal source) Glide: 500 μs to 1 s Rate: 0.26 Hz to 28 Hz (can be clocked from extrenal source) Slew rate: 1 ms to 3 s Portamento time: 0 to 10 s Attenuator 1: +4 dB to -∞ Attenuator 2: 0 dB to -∞ Cutoff frequency: 10 Hz to 15 kHz Resonance: 0 to 10 (capable of self oscillation) Modualtion depth: 0 to 100% Envelope depth: 0 to 100% Noise: 0 to 100% VCA bias: 0 to 100% Filter mode, high pass, band pass and low pass Filter key track: on/off Filter mode, high pass, band pass and low pass Shape: Sine, Triangle, Sawtooth, Square and Ramp Rate: 0 to 10 (0.01Hz to 10kHz) Key sync: on/off Rate/Level indicator Shape: Sine, Triangle, Sawtooth, Square and Ramp. Time: 25 ms to 640 ms Repeats: 0 to 100% Mix: 0 to 100% Overdrive Section Controls LED Inputs (TS 3.5 mm) OSC 1 OSC 2 OSC 1&2 INVERT IN SHAPE 1 SHAPE 2 PULSE WIDTH 1 PULSE WIDTH 2 VCF IN FREQ MOD RESONANCE OVERDRIVE IN VCA IN VCA CV DELAY IN DELAY TIME E GATE 1 E GATE 2 SAMPLE & HOLD IN SAMPLE & HOLD CLOCK LFO RATE LFO SHAPE LFO TRIG MULT (Multiple) ATT 1 IN ATT 1 CV ATT 2 IN SLEW IN SUM1(A) SUM1(B) SUM2(A) SUM2(B) Quick Start Guide 53 Drive: 0 to 11 Tone: 0 to 10 Level: 0 dB to -∞ Drive amount indicator Control voltage: 1 V per octave Control voltage: 1 V per octave Control voltage: 1 V per octave inverts voltage Control voltage: -5 V to +5 V Control voltage: -5 V to +5 V Control voltage: -5 V to +5 V Control voltage: -5 V to +5 V Signal input Control voltage: -5 V to +5 V Control voltage: -5 V to +5 V Signal input Signal input Control voltage: -9 V to +9 V Signal input Control voltage: -5 V to +5 V Control voltage: -5 V to +5 V (envelope triggers @ 1.5 V) Control voltage: -5 V to +5 V (envelope triggers @ 1.5 V) Signal input Control voltage: -5 V to +5 V (S&H triggers @ 3 V) Control voltage: -5 V to +5 V Control voltage: -5 V to +5 V Control voltage: -5 V to +5 V (S&H triggers @ 1.6 V) Input Signal is duplicated on Mult 1 and Mult 2 outputs Signal input Control voltage: -5 V to +5 V Signal input Signal or CV input Signal input or CV input Signal input or CV input Signal input or CV input Signal input or CV input