Bosch B18ID80NRP Use & Care Manual - Page 19

Warning, messages, Appliance, selfĆtest

Get Bosch B18ID80NRP PDF manuals and user guides View all Bosch B18ID80NRP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

Warning messages via the display If several warning messages are displayed simultaneously, deal with each message individually. While a warning message is displayed, buttons cannot be pressed aside from the alarm off button.15. Temperature alarm Door alarm Cause - An appliance door has not been closed properly or has been open too long. Remedial action q Close the door. The display goes out. Sensor fault Appliance selfĆtest Before you call customer service, conduct an appliance selfĆtest. q Switch off the appliance and wait 5 minutes. q Switch on the appliance. A temperature alarm is indicated by the required temperature flashing and the ALARM symbol coming on. A signal also sounds if the Tone function has been activated in setup mode. Cause - Power failure - Large quantities of fresh produce placed in the appliance - Fault with the appliance Remedial action q Press the alarm off button. The signal stops. The highest temperature in the appliance is displayed for several seconds. q Determine the cause of the temperature alarm. i When the required temperature is reached again, the ALARM symbol goes out and the signal stops. Cause - A technical defect is possible. Remedial action q Conduct an appliance selfĆtest. Low voltage The display light has gone out. Cause - The incoming mains voltage has dropped below the permitted limit value. Remedial action Buttons cannot be pressed. When the mains voltage reaches the stipulated value again, the warning message goes out. If the warning message is prolonged, inform your power supply company. q Simultaneously hold down the setup and alarm off buttons for 5 seconds. q The selfĆtest starts. Different messages are displayed in succession. If a fault is detected during the selfĆtest, the ALARM symbol and a corresponding error message, e.g. for a sensor fault, are displayed. Inform your dealer or appliance servicer about the error message. If the appliance selfĆtest does not establish any faults, the required temperature is displayed on completion of the selfĆtest. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
19
Warning
messages
via±the display
If
several warning
messages
are
displayed simultaneously,
deal with
each message
individually.
While
a
warning
message
is
displayed,
buttons
cannot
be
pressed aside
from the
alarm off
button.
15.
Temperature alarm
A temperature
alarm is
indicated
by
the
required temperature
flashing
and
the
ALARM
symbol coming
on.
A
signal
also
sounds
if
the
Tone
function has
been
activated
in
setup
mode.
Cause
-
Power failure
-
Large
quantities
of
fresh
produce
placed in the
appliance
-
Fault
with
the
appliance
Remedial action
q
Press
the
alarm off
button.
The signal stops.
The
highest
temperature
in
the
appliance
is
displayed for several seconds.
q
Determine
the
cause
of
the
temperature
alarm.
i
When
the
required
temperature
is
reached again, the
ALARM
symbol goes
out
and
the
signal
stops.
Door alarm
Cause
-
An appliance door
has not been
closed
properly
or
has
been
open too
long.
Remedial action
q
Close the door.
The
display
goes out.
Sensor fault
Cause
-
A technical defect is
possible.
Remedial action
q
Conduct an appliance selfĆtest.
Low voltage
The display
light has gone out.
Cause
-
The incoming
mains
voltage has
dropped
below
the permitted
limit
value.
Remedial action
Buttons cannot be pressed. When
the
mains voltage reaches
the
stipulated
value again, the warning
message goes
out. If
the warning
message is
prolonged, inform
your
power
supply
company.
Appliance
selfĆtest
Before you call customer service,
conduct an appliance selfĆtest.
q
Switch off
the appliance
and
wait 5
minutes.
q
Switch on the appliance.
q
Simultaneously
hold down
the
setup
and
alarm off
buttons for
5
seconds.
q
The selfĆtest starts.
Different²messages
are
displayed
in succession.
If
a fault is detected
during the
selfĆtest, the ALARM
symbol
and
a²corresponding
error
message,
e.g.²for
a sensor
fault, are
displayed.
Inform
your
dealer
or
appliance
servicer
about the error message.
If
the appliance selfĆtest
does not
establish any
faults, the
required
temperature is displayed on
completion of
the selfĆtest.