Bosch B21CL80SNS Instructions for Use - Page 7

Aligning the appliance, Connecting the appliance

Get Bosch B21CL80SNS PDF manuals and user guides View all Bosch B21CL80SNS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

Aligning the appliance NOTICE To ensure that the appliance operates correctly, use a level to align the appliance. If the appliance is not level, water may flow out of the ice maker, ice cubes may be irregular, or the doors may not close properly. 1. Place the appliance in the designated location. 2. So that the appliance cannot move, unscrew the two front feet until they are standing firmly on the floor. 3. Screw the feet in/out until the appliance is exactly level. 4. Use the level to check if the appliance is level. NOTICE To ensure that the appliance does not move, the front feet must be firmly planted on the floor. 5. If the height of the refrigerator compartment doors are uneven or if the freezer compartment drawer is slanted after adjusting the level of the appliance, use the following method to adjust them. Adjusting the refrigerator doors The appliance must be level in order to get the doors to align. 1. Raise the lower door up to the level of the higher door. en-us 2. Insert the supplied fastener-ring (A) using a pair of pliers (B) in the gap between the hinge-grommet (C) and the lower hinge (D). The number of fasten-rings you will need to insert depends on the gap. B C A D Installing the base plate 1. Mount the base plate. 2. Insert the three screws and tighten. Connecting the appliance Have a technician install and connect the appliance according to the enclosed Installation Instructions. Do not remove the transportation protection devices from the shelves and storage compartments until the appliance has been installed and aligned. Always connect the water before the power. Apart from statutory national regulations, you should comply with all applicable local electricity and water companies codes and requirements. After installing the appliance, wait at least 6 hours before switching the appliance on. During transportation the oil in the compressor may have flowed into the refrigeration system. Before switching the appliance on for the first time, clean the interior of the appliance (see chapter "Cleaning the Appliance"). 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
en-us
7
Aligning the appliance
NOTICE
To ensure that the appliance operates correctly, use
a level to align the appliance.
If the appliance is not level, water may flow out of the
ice maker, ice cubes may be irregular, or the doors
may not close properly.
1.
Place the appliance in the designated location.
2.
So that the appliance cannot move, unscrew the
two front feet until they are standing firmly on the
floor.
3.
Screw the feet in/out until the appliance is exactly
level.
4.
Use the level to check if the appliance is level.
NOTICE
To ensure that the appliance does not move, the
front feet must be firmly planted on the floor.
5.
If the height of the refrigerator compartment doors
are uneven or if the freezer compartment drawer is
slanted after adjusting the level of the appliance,
use the following method to adjust them.
Adjusting the refrigerator doors
The appliance must be level in order to get the doors
to align.
1.
Raise the lower door up to the level of the higher
door.
2.
Insert the supplied fastener-ring (
A
) using a pair of
pliers (
B
) in the gap between the
hinge-grommet (
C
) and the lower hinge (
D
). The
number of fasten-rings you will need to insert
depends on the gap.
D
B
A
C
Installing the base plate
1.
Mount the base plate.
2.
Insert the three screws and tighten.
Connecting the appliance
Have a technician install and connect the appliance
according to the enclosed Installation Instructions.
Do not remove the transportation protection devices
from the shelves and storage compartments until the
appliance has been installed and aligned.
Always connect the water before the power.
Apart from statutory national regulations, you should
comply with all applicable local electricity and water
companies codes and requirements.
After installing the appliance, wait at least 6 hours
before switching the appliance on. During
transportation the oil in the compressor may have
flowed into the refrigeration system.
Before switching the appliance on for the first time,
clean the interior of the appliance (see chapter
“Cleaning the Appliance”).