Bosch SHX4AP06UC Use and Care Manual - Page 18

Operating, the Dishwasher

Get Bosch SHX4AP06UC - 24' Ascenta Series Dishwasher PDF manuals and user guides
UPC - 825225878742
View all Bosch SHX4AP06UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Operating the Dishwasher SHX4AP, SHXSAL, SHX6AP Depending on your model you will either have 4, 5 or 5 wash cydes. To start the dishwasher: • Open the Door. Press the"ON/OFF" button. • One of the Wash Cycle LEDs will be flashing. You can now select a wash cycle. • Press the "" button to select the desired wash cycle. • Press the "START" button (LED stops flashing) • Close the door to begin the cycle NOTE 1. Rinse Agent Indicator Light will be illuminated if the unit needs Rinse Agent. 2. If you close the door without pressing the start button the unit will beep. To cancel a cycle: • Open the dishwasher door just far enough to expose the control panel. Be careful of hot water splash out! • Press and hold the "START/RESET" button until the "Active" indicator light goes out. • The "Clean" and one other LED will be flashing. You are now in the options setup mode. • Press ">" to select the option you would like to adjust. If the "Clean" and "Rinse Agent" LED are flashing you can adjust the Rinse Agent settings. If the "Clean" and "Sanitized" LED are flashing you can set the Extra Dry Heat. To set the amount of Rinse Agent: NOTE: If your glasses have spots on them, you need more rinse agent. If your glasses have streaks, you need less Rinse Agent. Follow the prior instructions to enter "options" mode. With the "Clean" and "Rinse Agent" LEDs flashing: • Press the "

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Operating
the Dishwasher
SHX4AP, SHXSAL, SHX6AP
Depending
on your model you will either have 4, 5 or 5 wash
cydes.
To start
the
dishwasher:
•
Open the Door. Press the"ON/OFF"
button.
•
One of the Wash Cycle LEDs will
be flashing.
You can
now
select a wash cycle.
•
Press the "<" or ">" button
to select the desired wash
cycle.
•
Press the "START" button
(LED stops flashing)
•
Close the door to begin
the cycle
NOTE
1.
Rinse Agent
Indicator
Light will
be illuminated
if the
unit needs Rinse Agent.
2.
If you close the door without
pressing the start button
the unit will
beep.
To cancel
a cycle:
•
Open the dishwasher
door just far enough
to expose
the control
panel. Be careful of hot water splash out!
•
Press and
hold
the
"START/RESET" button
until
the
"Active" indicator
light
goes out.
You could be seriously
scalded if you allow
hot water
to splash out of the dishwasher.
OPEN THE DOOR
CAREFULLY during
any wash or rinse cycle. Do not fully
open the door
until
water
noises have stopped.
•
Close the
door
and wait
for about
1 minute
for
the
dishwasher
to drain.
•
The unit will
beep when done draining.
•
Open the door
and press the"ON/OFF'
button.
•
You are now
ready to start a new cycle.
To enter
the
options
mode
(rinse
agent
setting,
ex-
tra
dry
heat,
cycle
completion
signal):
•
Door
must
be open.
Press the
"ON/OFF"
button
to
turn
the unit on.
•
One of the Wash Cycle LEDs will
be flashing.
•
Press and hold
down
the ">" button,
then press and
release the
"START/RESET" button.
Now
release the
">" button.
18
•
The "Clean" and one
other
LED will
be flashing.
You
are now in the options
setup
mode.
•
Press ">"
to
select
the
option
you
would
like
to
adjust.
If the "Clean" and "Rinse Agent"
LED are flashing
you can
adjust the Rinse Agent settings.
If the "Clean" and "Sanitized"
LED are flashing
you can set
the Extra Dry Heat.
To set the
amount
of Rinse
Agent:
NOTE: If your glasses have spots on them, you need more
rinse
agent.
If your
glasses have streaks, you
need
less
Rinse Agent.
Follow
the
prior
instructions
to
enter
"options"
mode.
With the "Clean" and "Rinse
Agent"
LEDs flashing:
•
Press the "<" button
to
change
the amount
of rinse
agent dispensed.
0 LEDs flashing
-->
Rinse Agent dispenser is OFF
1 LED flashing
-->
Lowest amount
of rinse agent
2 LEDs flashing
-->
Medium
amount
dispensed
3
LEDs flashing
-->
Highest amount
of rinse agent
Press "START"to save your settings.
To turn
Extra
Dry
Heat
on or off:
With the "Clean" and "Sanitized"
LEDs flashing:
•
Press the "<" button
to turn
Extra Dry Heat on or o[&
The wash
cycle
LEDs will
illuminate
when
you press
II
_II.
0 LEDs flashing
-->
Extra Dry Heat is OFF
1 LED flashing
-->
Extra DryHeatis
ON
To set the
Cycle
Completion
Signal:
With
the
"Clean",
"Sanitized",
and
"Rinse Agent"
LEDs
flashing:
•
Press the "<" button
to change
the cycle completion
tone
level. The wash cycle LEDs will
illuminate
when
you press "<".
0 LEDs flashing
-->
Cycle Completion
Signal is OFF
1 LED flashing
-->
Low tone level
2 LEDs flashing
-->
Medium
tone level
3
LEDs flashing
-->
Highest tone level
•
Press STARTto save your settings.