Brother International HE-120 Users Manual - English - Page 25

Caution

Page 25 highlights

SE-BrotherE_sgml.book Page 19 Monday, June 30, 2003 3:44 PM Place the bobbin on the bobbin winder shaft so d that the spring on the shaft fits into the notch Slide the spool cap onto the bobbin thread g spool pin. in the bobbin. With the rounded side of the spool cap positioned toward the left, slide the spool cap onto the bobbin thread spool pin as far as possible until the right side of the spool touches 1 1 the right end of the bobbin thread spool pin. 2 a Notch b Bobbin winder shaft spring Slide the bobbin winder shaft to the right. e Place the spool of thread for the bobbin onto f the bobbin thread spool pin. CAUTION ● Two spool cap sizes are available, allowing you to choose a spool cap that best fits the size of spool being used. If the spool cap is too small for the spool being used, the thread may catch on the slit in the spool or the needle may break. ● • Use the special Brother embroidery bobbin thread when embroidering. Note z If a spool of thread 12 mm (1/2 inch) in diameter and 75 mm (3 inch) high is inserted onto the bobbin thread spool pin, use the special spool cap. 2 1 a 12 mm (1/2 inch) b 75 mm (3 inch) Winding/Installing the Bobbin 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183

Winding/Installing the Bobbin
19
1
— — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — — —
d
Place the bobbin on the bobbin winder shaft so
that the spring on the shaft fits into the notch
in the bobbin.
a
Notch
b
Bobbin winder shaft spring
e
Slide the bobbin winder shaft to the right.
f
Place the spool of thread for the bobbin onto
the bobbin thread spool pin.
• Use the special Brother embroidery bobbin
thread when embroidering.
g
Slide the spool cap onto the bobbin thread
spool pin.
With the rounded side of the spool cap
positioned toward the left, slide the spool cap
onto the bobbin thread spool pin as far as
possible until the right side of the spool touches
the right end of the bobbin thread spool pin.
CAUTION
Note
If a spool of thread 12 mm (1/2 inch) in
diameter and 75 mm (3 inch) high is inserted
onto the bobbin thread spool pin, use the
special spool cap.
a
12 mm (1/2 inch)
b
75 mm (3 inch)
1
2
Two spool cap sizes are available,
allowing you to choose a spool cap that
best fits the size of spool being used. If the
spool cap is too small for the spool being
used, the thread may catch on the slit in
the spool or the needle may break.
1
2
SE-BrotherE_sgml.book
Page 19
Monday, June 30, 2003
3:44 PM