Brother International RH-981A Instruction Manual - Spanish - Page 81

Changing Functions Using The Dip Switches, 11-1. Panel Dip Switches

Get Brother International RH-981A PDF manuals and user guides View all Brother International RH-981A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

11. CHANGING FUNCTIONS USING THE DIP SWICHES 11. CHANGING FUNCTIONS USING THE DIP SWITCHES Always turn off the power supply before changing any of the DIP switch settings. 11-1. Panel DIP switches The ON/OFF positions of the DIP switches inside the operation panel are checked only once when the power is turned on. Any changes to the DIP switch positions will not be effective until the power is switched off and back on again. 2425Q No. ON/OFF Setting items ON Program mode disabled 1* OFF Program mode enabled ON Switches between taper bar ←→ straight bar tacking 2 OFF Normal ON Set the feed bracket to the front position 3 OFF Set the feed bracket to the back position ON - 4 OFF - ON Single-pedal operation 5 OFF Dual-pedal operation ON - 6 OFF - ON - 7 OFF - ON Maximum stitch width correction amount = 2.0 mm 8** OFF Maximum stitch width correction amount = 1.0 mm Default OFF OFF OFF OFF OFF OFF OFF OFF * If program mode is disabled, operation becomes as follows. • Program numbers, knife operations and the production counter cannot be changed. • The modes change in the order Automatic → Test feed → Manual → Automatic. ** If the maximum stitch width correction amount is set to 2.0 mm, carry out the adjustment in "9-14. Adjusting the position of the work clamp plate". If this adjustment is not carried out, the throat plate and needle plate may interfere with each other. If the stitch width correction amount is set to more than 1.0 mm, the sewing speed will be limited in accordance with the value set. RH-981A 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
11. CHANGING FUNCTIONS USING THE DIP SWICHES
RH-981A
74
11. CHANGING FUNCTIONS USING THE DIP SWITCHES
Always turn off the power supply before changing any of the DIP switch settings.
11-1. Panel DIP switches
The ON/OFF positions of the DIP switches inside the operation panel are checked only once when the power is
turned on.
Any changes to the DIP switch positions will not be effective until the power is switched off and back on again.
No.
ON/OFF
Setting items
Default
ON
Program mode disabled
1*
OFF
Program mode enabled
OFF
ON
Switches between taper bar
←→
straight bar tacking
2
OFF
Normal
OFF
ON
Set the feed bracket to the front position
3
OFF
Set the feed bracket to the back position
OFF
ON
-
4
OFF
-
OFF
ON
Single-pedal operation
5
OFF
Dual-pedal operation
OFF
ON
-
6
OFF
-
OFF
ON
-
7
OFF
-
OFF
ON
Maximum stitch width correction amount = 2.0 mm
8**
OFF
Maximum stitch width correction amount = 1.0 mm
OFF
*
If program mode is disabled, operation becomes as follows.
•
Program numbers, knife operations and the production counter cannot be changed.
•
The modes change in the order Automatic
→
Test feed
→
Manual
→
Automatic.
** If the maximum stitch width correction amount is set to 2.0 mm, carry out the adjustment in "9-14. Adjusting the
position of the work clamp plate". If this adjustment is not carried out, the throat plate and needle plate may
interfere with each other.
If the stitch width correction amount is set to more than 1.0 mm, the sewing speed will be limited in accordance
with the value set.
2425Q