Brother International XR9550 Operation Manual - Page 13

Threading The Machine

Get Brother International XR9550 PDF manuals and user guides View all Brother International XR9550 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Cancelling the operation beep When the sewing machine is purchased, it is set to beep each time a key is pressed. This setting can be changed so that the machine does not beep. 1 Turn off the sewing machine. 2 Holding the "-" side of (3) pressed, turn on the sewing machine.  3 After the sewing machine has turned on, release the "-" side of (3). XX The machine is now set so that it will not beep. Memo • Perform the same operation to change the setting so that machine beeps. THREADING THE MACHINE Winding the bobbin This section describes how to wind the thread onto the bobbin. • For details on the fast bobbin winding, see page 13. KNOWING YOUR SEWING MACHINE CAUTION • Only use the bobbin that comes with this machine or bobbins of the same type (part code: SA156, SFB: XA5539-151). Using other bobbins may cause damage to the machine. 1 SA156 is Class 15 type bobbin. Actual size 11.5 mm (7/16 inch) This model Other models 1 Press down on the spool pin lever to swing up the spool pin. Then remove the spool cap. 1 Spool pin 2 Spool cap CAUTION • Do not grab the bar to raise the spool pin, otherwise, the spool pin may bend or break. • Be sure to raise the spool pin when winding the bobbin. The thread may become tangled if the bobbin winder is used without raising the spool pin. 2 Fully insert the spool of thread for the bobbin, and then slide the spool cap onto the spool pin. 1 Bobbin-winding thread guide 2 Bobbin winder shaft 3 Bobbin • The thread should be unwound from the bottom to the front. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
KNOWING YOUR SEWING MACHINE
11
1
Cancelling the operation beep
When the sewing machine is purchased, it is set to
beep each time a key is pressed. This setting can be
changed so that the machine does not beep.
1
Turn off the sewing machine.
2
Holding the “–” side of
(
3
) pressed,
turn on the sewing machine.
²
3
After the sewing machine has turned on,
release the “–” side of
(
3
).
X
The machine is now set so that it will not
beep.
Memo
• Perform the same operation to change the setting
so that machine beeps.
THREADING THE MACHINE
Winding the bobbin
This section describes how to wind the thread onto
the bobbin.
•
For details on the fast bobbin winding, see page
13.
1
Bobbin-winding thread guide
2
Bobbin winder shaft
3
Bobbin
CAUTION
•
Only use the bobbin that comes with this
machine or bobbins of the same type (part
code: SA156, SFB: XA5539-151). Using other
bobbins may cause damage to the machine.
SA156 is Class 15 type bobbin.
This model
Actual size
11.5 mm
(7/16 inch)
Other models
1
Press down on the spool pin lever to swing
up the spool pin. Then remove the spool cap.
1
Spool pin
2
Spool cap
CAUTION
•
Do not grab the bar to raise the spool pin,
otherwise, the spool pin may bend or break.
•
Be sure to raise the spool pin when winding
the bobbin. The thread may become tangled if
the bobbin winder is used without raising the
spool pin.
2
Fully insert the spool of thread for the
bobbin, and then slide the spool cap onto the
spool pin.
•
The thread should be unwound from the
bottom to the front.