Campbell Scientific WINDSONIC1 WINDSONIC 2-D Sonic Wind Sensors - Page 31

SDI-12 Transparent Mode on an Edlog array-based

Get Campbell Scientific WINDSONIC1 PDF manuals and user guides View all Campbell Scientific WINDSONIC1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

WindSonic Two-Dimensional Sonic Anemometer • To activate the SDI-12 Transparent Mode, on Control Port p, enter pX and press the key. The datalogger will respond with "entering SDI12". If any invalid SDI-12 command is issued, the datalogger will exit the SDI-12 Transparent Mode. • To query the WindSonic4 for its current SDI-12 address, enter the command ?!. The WindSonic4 will respond with the current SDI-12 address. • To change the SDI-12 address, enter the command aAb!; where a is the current address from the above step and b is the new address. The WindSonic4 will change its address and the datalogger will exit the SDI12 Transparent Mode. • To activate the SDI-12 Transparent Mode on Control Port p, enter pX and press the key. Verify the new SDI-12 address by entering the "?!" command. The WindSonic4 will respond with the new address. • To exit the SDI-12 Transparent Mode, enter ∗. FIGURE 7-1. SDI-12 Transparent Mode on an Edlog array-based datalogger (CR10X) using control port 8 and changing the SDI-12 address from 0 to 1 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
WindSonic Two-Dimensional Sonic Anemometer
•
To activate the SDI-12 Transparent Mode, on Control Port
p
, enter
p
X and
press the <enter> key.
The datalogger will respond with “entering SDI-
12”.
If any invalid SDI-12 command is issued, the datalogger will exit the
SDI-12 Transparent Mode.
•
To query the WindSonic4 for its current SDI-12 address, enter the
command
?!
.
The WindSonic4 will respond with the current SDI-12
address.
•
To change the SDI-12 address, enter the command
a
A
b
!
; where
a
is the
current address from the above step and
b
is the new address.
The
WindSonic4 will change its address and the datalogger will exit the SDI-
12 Transparent Mode.
•
To activate the SDI-12 Transparent Mode on Control Port
p
, enter
p
X and
press the <enter> key.
Verify the new SDI-12 address by entering the “?!”
command.
The WindSonic4 will respond with the new address.
•
To exit the SDI-12 Transparent Mode, enter
∗
.
FIGURE 7-1.
SDI-12 Transparent Mode on an Edlog array-based
datalogger (CR10X) using control port 8 and changing the SDI-12
address from 0 to 1
23