Canon 0304B001 User Manual - Page 176

Troubleshooting Guide

Get Canon 0304B001 - EOS 1D Mark II N Digital Camera SLR PDF manuals and user guides
UPC - 013803056648
View all Canon 0304B001 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 176 highlights

Troubleshooting Guide If there is a problem, first refer to this Troubleshooting Guide. Power Source The battery cannot be recharged. You are using the wrong battery. X Use the dedicated Ni-MH Pack. (p.22) The battery is not properly attached to the charger. X Attach the battery properly to the charger. (p.22) The camera does not operate even when the switch is set to . The battery is exhausted. X Recharge the battery. (p.22) The battery is not installed properly. X Install the battery properly. (p.25) The memory card slot is open. X Push in the memory card and close the memory card slot. (p.30) The access lamp lights or blinks even when the switch is set to . If you set the switch to right after shooting, the access lamp will still light or blink for a few seconds while the image is recorded onto the memory card. X When the camera finishes recording the image to the memory card, the access lamp will stop blinking and the power will turn off. The battery becomes exhausted quickly. The battery is not fully charged. X Recharge the battery fully. (p.22) The battery's service life has expired. X Replace it with a new battery. (p.182) 176

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
176
If there is a problem, first refer to this Troubleshooting Guide.
You are using the wrong battery.
Use the dedicated Ni-MH Pack. (p.22)
The battery is not properly attached to the charger.
Attach the battery properly to the charger. (p.22)
The battery is exhausted.
Recharge the battery. (p.22)
The battery is not installed properly.
Install the battery properly. (p.25)
The memory card slot is open.
Push in the memory card and close the memory card slot. (p.30)
If you set the <
4
> switch to <
2
> right after shooting, the
access lamp will still light or blink for a few seconds while the
image is recorded onto the memory card.
When the camera finishes recording the image to the memory
card, the access lamp will stop blinking and the power will turn off.
The battery is not fully charged.
Recharge the battery fully. (p.22)
The battery’s service life has expired.
Replace it with a new battery. (p.182)
Troubleshooting Guide
Power Source
The battery cannot be recharged.
The camera does not operate even when the <
4
> switch is set to <
1
>.
The access lamp lights or blinks even when the
<
4
> switch is set to <
2
>.
The battery becomes exhausted quickly.