Canon LV-7280 User Manual - Page 83

Appendix, (1) Troubleshooting, Indicator Messages

Get Canon LV-7280 PDF manuals and user guides View all Canon LV-7280 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

7. Appendix  Troubleshooting This section helps you resolve problems you may encounter while setting up or using the projector. STATUS Indicator LAMP Indicator Indicator Messages POWER Indicator POWER Indicator Indicator Condition Off 0.5 sec On, Blinking light Green 0.5 sec Off 2.5 sec On, 0.5 sec Off Green Steady light Orange Red Projector Condition The main power is off The projector is getting ready to turn on. Off Timer is enabled. The projector is turned on. [Normal] is selected for [Standby mode] [Power-saving] is selected for [Standby mode] - Wait for a moment. - - - Note STATUS Indicator Indicator Condition Projector Condition Off Normal 1 cycle (0.5 sec 2.5 sec Off) On, Lamp cover error or lamp housing error 2 cycle (0.5 sec 0.5 sec Off) On, Temperature error 3 cycle (0.5 sec 0.5 sec Off) On, Power error Red Blinking light 4 cycle (0.5 sec 0.5 sec Off) On, Fan error 6 cycle (0.5 sec 0.5 sec Off) On, Lamp error 9 cycle 0.5 sec (0.5 Off) sec On, [Auto iris] error Green Re-firing the lamp Green Standby([Normal] for [Standby mode]) Steady light Orange Key lock is on. Note - Replace the lamp cover or lamp correctly. See page 73. The projector is overheated. Move the projector to a cooler location. Power unit is not working properly. Contact your dealer Fans will not work correctly. Lamp fails to light. Wait a full minute and then turn on again. The Auto iris function is not working properly. (LV-7285 and LV-7280). Contact your dealer. The projector is re-firing. Wait for a moment. - You have pressed cabinet button when Key lock is on. See page 62. LAMP Indicator Indicator Condition Projector Condition Note Off Normal - Blinking light Red Lamp has played. reached its end of life. Lamp replacement message will be dis- Replace the lamp. Steady light Red Lamp has been used beyond the lamp is replaced. its limit. The projector will not turn on until Replace the lamp. Green* Lamp mode is set to Quiet mode. - * This indicator lights green for about 90 seconds immediately after the projector is powered on. If a temperature error occurs If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the STATUS indicator blinking (2-cycle On and Off.) Should this happen, do the following: - Turn off the main power and unplug the AC power cord. - Move the projector to a cooler location if the room where you are presenting is particularly too warm. - Clean the ventilation holes if they are clogged with dust. - Wait about 60 minutes until the inside of the projector becomes cool enough. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
74
7. Appendix
Troubleshooting
This section helps you resolve problems you may encounter while setting up or using the projector.
Indicator Messages
POWER Indicator
Indicator Condition
Projector Condition
Note
Off
The main power is off
–
Blinking light
Green
0.5 sec On,
0.5 sec Off
The projector is getting ready to turn on.
Wait for a moment.
2.5 sec On,
0.5 sec Off
Off Timer is enabled.
–
Steady light
Green
The projector is turned on.
–
Orange
[Normal] is selected for [Standby mode]
Red
[Power-saving] is selected for [Standby mode]
–
STATUS Indicator
Indicator Condition
Projector Condition
Note
Off
Normal
–
Blinking light
Red
1 cycle (0.5 sec On,
2.5 sec Off)
Lamp cover error or lamp housing error
Replace the lamp cover or lamp correctly.
See page
73
.
2 cycle (0.5 sec On,
0.5 sec Off)
Temperature error
The projector is overheated. Move the projector to a cooler
location.
3 cycle (0.5 sec On,
0.5 sec Off)
Power error
Power unit is not working properly.
Contact your dealer
4 cycle (0.5 sec On,
0.5 sec Off)
Fan error
Fans will not work correctly.
6 cycle (0.5 sec On,
0.5 sec Off)
Lamp error
Lamp fails to light. Wait a full minute and then turn on
again.
9 cycle (0.5 sec On,
0.5 sec Off)
[Auto iris] error
The Auto iris function is not working properly. (LV-7285
and LV-7280). Contact your dealer.
Green
Re-firing the lamp
The projector is re-firing. Wait for a moment.
Steady light
Green
Standby([Normal] for [Standby mode])
–
Orange
Key lock is on.
You have pressed cabinet button when Key lock is on.
See page
62
.
LAMP Indicator
Indicator Condition
Projector Condition
Note
Off
Normal
–
Blinking light
Red
Lamp has reached its end of life. Lamp replacement message will be dis-
played.
Replace the lamp.
Steady light
Red
Lamp has been used beyond its limit. The projector will not turn on until
the lamp is replaced.
Replace the lamp.
Green*
Lamp mode is set to Quiet mode.
–
* This indicator lights green for about 90 seconds immediately after the projector is powered on.
If a temperature error occurs
If the temperature inside the projector rises too high, the over-temperature protector will automatically turn off the lamp with the
STATUS indicator blinking (2-cycle On and Off.)
Should this happen, do the following:
- Turn off the main power and unplug the AC power cord.
- Move the projector to a cooler location if the room where you are presenting is particularly too warm.
- Clean the ventilation holes if they are clogged with dust.
- Wait about 60 minutes until the inside of the projector becomes cool enough.
POWER Indicator
STATUS Indicator
LAMP Indicator