Canon MP830 Service Manual - Page 13

Fax Errors, Initial identification T0 / T1 time-over - logic board

Get Canon MP830 - PIXMA Color Inkjet PDF manuals and user guides
UPC - 013803052725
View all Canon MP830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

blinking Alarm LED lit RAM error hard-power-on. [6300] The RAM error occurred in the RAM check at hardpower-on. - Logic board Note: Before replacement of the logic board ass'y, check the waste ink amount (by service test print or EEPROM information print). If the waste ink amount is 7% or more, also replace the ink absorber kit (QY5-0153) when replacing the logic board ass'y. [See Section 3-3. Adjustment / Settings, (6) Service mode, for details.] 2-3. Fax Errors For errors other than those listed below, please refer to the "G3 / G4 Facsimile Error Code List (Rev. 2)." (1) User error codes Error code TX / RX Meaning #001 TX Document jam #003 TX / RX Document is too long, or page time-over #005 TX / RX Initial identification (T0 / T1) time-over #009 RX Recording paper jam, or no recording paper #012 TX No recording paper at the receiving machine #017 TX Redial time-over, but no DT detected #018 TX Auto dialing transmission error, or redial time-over #022 TX Call failed (no dial registration) #037 RX Memory overflow at reception of an image #085 TX No color fax function supported in the receiving machine #099 TX / RX Transmission terminated mid-way by pressing the Stop/Reset button #995 TX / RX During TX (sending): Memory transmission reservation cancelled During RX (receiving): Image data received in the memory cleared (2) Service error codes Error code TX / RX Meaning ##100 TX Re-transmission of the procedure signal has been attempted the specified number of times, but failed. ##101 TX / RX Sender's modem speed does not match the receiving machine. ##102 TX Fallback is not available. ##103 RX EOL has not been detected for 5 seconds (or 15 seconds in CBT). ##104 TX RTN or PIN has been received. ##106 RX The procedure signal has been expected for 6 seconds, but not received. ##107 RX Fallback is not available at the sending machine. ##109 TX After DCS transmission, a signal other than DIS, DTC, FTT, CFR, or CRP has been received, and re-transmission of the procedure signal has been attempted the specified number of times but failed. ##111 TX / RX Memory error ##114 RX RTN has been received. ##200 RX A carrier has not been detected for 5 seconds during image reception. ##201 TX / RX DCN has been received in a method other than the binary procedure. ##204 TX DTC has been received even when there is no sending data. ##220 TX / RX System error (main program hang-up) ##224 TX / RX An error has occurred in the procedure signal in G3 transmission. ##226 TX / RX The stack pointer has shifted from the RAM area. ##229 RX The recording area has been locked for 1 minute. ##232 TX The encoder control unit has malfunctioned. ##237 RX The decoder control unit has malfunctioned. ##238 RX The print control unit has malfunctioned. ##261 TX / RX A system error has occurred between the modem and the system control board. 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
Note:
Before replacement of the logic board ass'y, check the waste ink amount (by service test print or EEPROM information print). If the
waste ink amount is 7% or more, also replace the ink absorber kit (QY5-0153) when replacing the logic board ass'y. [See
Section 3-3.
Adjustment / Settings, (6) Service mode
, for details.]
2-3.
Fax Errors
For errors other than those listed below, please refer to the "
G3 / G4 Facsimile Error Code List (Rev. 2).
"
(1)
User error codes
(2)
Service error codes
blinking
hard-power-on.
Alarm LED lit
RAM error
[6300]
The RAM error occurred in the RAM check at hard-
power-on.
- Logic board
Error code
TX / RX
Meaning
#001
TX
Document jam
#003
TX / RX
Document is too long, or page time-over
#005
TX / RX
Initial identification (T0 / T1) time-over
#009
RX
Recording paper jam, or no recording paper
#012
TX
No recording paper at the receiving machine
#017
TX
Redial time-over, but no DT detected
#018
TX
Auto dialing transmission error, or redial time-over
#022
TX
Call failed (no dial registration)
#037
RX
Memory overflow at reception of an image
#085
TX
No color fax function supported in the receiving machine
#099
TX / RX
Transmission terminated mid-way by pressing the Stop/Reset button
#995
TX / RX
During TX (sending):
Memory transmission reservation cancelled
During RX (receiving):
Image data received in the memory cleared
Error code
TX / RX
Meaning
##100
TX
Re-transmission of the procedure signal has been attempted the specified number of times, but failed.
##101
TX / RX
Sender's modem speed does not match the receiving machine.
##102
TX
Fallback is not available.
##103
RX
EOL has not been detected for 5 seconds (or 15 seconds in CBT).
##104
TX
RTN or PIN has been received.
##106
RX
The procedure signal has been expected for 6 seconds, but not received.
##107
RX
Fallback is not available at the sending machine.
##109
TX
After DCS transmission, a signal other than DIS, DTC, FTT, CFR, or CRP has been received, and re-transmission of the
procedure signal has been attempted the specified number of times but failed.
##111
TX / RX
Memory error
##114
RX
RTN has been received.
##200
RX
A carrier has not been detected for 5 seconds during image reception.
##201
TX / RX
DCN has been received in a method other than the binary procedure.
##204
TX
DTC has been received even when there is no sending data.
##220
TX / RX
System error (main program hang-up)
##224
TX / RX
An error has occurred in the procedure signal in G3 transmission.
##226
TX / RX
The stack pointer has shifted from the RAM area.
##229
RX
The recording area has been locked for 1 minute.
##232
TX
The encoder control unit has malfunctioned.
##237
RX
The decoder control unit has malfunctioned.
##238
RX
The print control unit has malfunctioned.
##261
TX / RX
A system error has occurred between the modem and the system control board.
1-7