Canon MultiPASS F20 MultiPASS F20 Basic Guide - Page 79

Problems printing from your computer - driver windows 7

Get Canon MultiPASS F20 PDF manuals and user guides View all Canon MultiPASS F20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

6. Did you disconnect then reconnect the USB cable during standby? Reconnect the USB cable. Problems printing from your computer See below if you have tried unsuccessfully to print from your computer, or if you cannot print images scanned to your computer. The P mark indicates problems that also occur when printing copies on your machine. Cannot print at all. 1. Is there anything displayed in the LCD? If nothing is displayed, see p. 10-10. 2. Is the Alarm light blinking? If it is blinking, see p. 10-12. 3. Is there a warning or attention displayed in the Status Monitor? If displayed, see p. 10-16. P 4. Print the nozzle check pattern ( Maintaining the printhead, p. 9-5). 5. Are you trying to print in DOS? You can only print in Windows and not in DOS. 6. Is there an application error or General Protection Fault error displayed on the computer? Is the application you are using to print compatible with the operating system? Refer to the application's documentation. If the application is not compatible, generally you will be unable to print. Has the application been allocated enough memory? If other applications are open, close them to increase the available memory. Refer to the application's documentation to check the amount of memory the application requires. If a problem occurs when printing a specific document Try printing again after opening and editing the document. 7. Does the hard disk have enough available space? 10 If not, delete files you do not need to increase the available disk space. 8. Restart the computer. 9. There may be a problem with the printer driver. Remove the MultiPASS Suite software and try reinstalling. To remove the MultiPASS Suite, see the Software Guide. To install, see the Setup Sheet. Troubleshooting Cannot print to a shared printer. 1. Is the server (the computer to which the machine is connected) turned on? Turn the server on. 2. Is the server set up for printer sharing? Set up the server for printer sharing ( Software Guide). 3. Is the server set up to allow your system access to the shared printer? Set up the server to allow your system access to the shared printer. Chapter 10 Troubleshooting 10-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
Chapter 10
Troubleshooting
10-3
10
Troubleshooting
6.
Did you disconnect then reconnect the USB cable during standby?
Reconnect the USB cable.
±
Problems printing from your computer
See below if you have tried unsuccessfully to print from your computer,or if you cannot
print images scanned to your computer.
The
mark indicates problems that also occur when printing copies on your machine.
±
Cannot print at all.
1.
Is there anything displayed in the LCD?
If nothing is displayed, see p. 10-10.
2.
Is the Alarm light blinking?
If it is blinking, see p. 10-12.
3.
Is there a warning or attention displayed in the Status Monitor?
If displayed, see p. 10-16.
4.
Print the nozzle check pattern (
²
Maintaining the printhead
, p. 9-5).
5.
Are you trying to print in DOS?
You can only print in Windows and not in DOS.
6.
Is there an application error or General Protection Fault error displayed on the computer?
Is the application you are using to print compatible with the operating system?
Refer to the application’s documentation.If the application is not compatible, generally you will be
unable to print.
Has the application been allocated enough memory?
If other applications are open, close them to increase the available memory.
Refer to the application’s documentation to check the amount of memory the application requires.
If a problem occurs when printing a specific document
Try printing again after opening and editing the document.
7.
Does the hard disk have enough available space?
If not, delete files you do not need to increase the available disk space.
8.
Restart the computer.
9.
There may be a problem with the printer driver.
Remove the MultiPASS Suite software and try reinstalling.
To remove the MultiPASS Suite,see the
Software Guide
. To install, see the
Setup Sheet
.
±
Cannot print to a shared printer.
1.
Is the server (the computer to which the machine is connected) turned on?
Turn the server on.
2.
Is the server set up for printer sharing?
Set up the server for printer sharing (
²
Software Guide
).
3.
Is the server set up to allow your system access to the shared printer?
Set up the server to allow your system access to the shared printer.
P
P