Canon REALiS LCOS WUX6000 MULTIMEDIA PROJECTOR WUX6000 Users Manual
Canon REALiS LCOS WUX6000 Manual
View all Canon REALiS LCOS WUX6000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Canon REALiS LCOS WUX6000 manual content summary:
- Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 1
MULTIMEDIA PROJECTOR User's Manual Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 2
quality digital image on a large screen. This Manual This is the user's manual for WUX6000 Multimedia Projectors. The "Operation" section by a qualified technician, if possible. Contact the Canon Customer Support Center for further information. Symbols of Button Operations The projector can - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 3
How to Use This Manual Copyright Notice Please note that enlarging or reducing the size of an image for commercial purposes or public presentation may infringe on the legally protected - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 4
. (P153) Networked Multi-Projection (NMPJ) Project images from multiple computers via a network connection. For details on Networked Multi-Projection (NMPJ), refer to the separate user's manual. 4 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 5
Disabling the Beep During Operation (P100) Disabling Buttons (P101) Hiding Guide Messages (P149) Setting a Password (P104) Reducing the Lamp on Networked Multi-Projection (NMPJ), refer to the separate user's manual.) Producing a Presentation Temporarily Blacking Out an Image (P62) Freezing - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 6
Table of Contents How to Use This Manual 2 Projector Highlights 4 Quick Reference Guide 5 Safety Instructions 10 Safety Precautions 11 CAUTION ON HANGING FROM THE CEILING 11 AC Power Cord Requirement 14 Federal Communication Commission Notice 15 Precautions for Use 17 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 7
Table of Contents Table of Contents Selecting an Input Signal (Analog PC Input 76 Adjusting the Input Signal (Total dots 77 Adjusting the Input Signal (Tracking 77 Adjusting the Input Signal (Horizontal / Vertical position 78 Adjusting the Input Signal (Horizontal / Vertical pixels 78 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 8
Screen Color Adjustment 148 Specifying a Menu Position 149 Showing/Hiding the Guide Screen ... 149 Showing/Hiding Input Status 150 Showing/Hiding Overheat Warnings 150 Replacing the Lamp 199 Appendix Appendix 201 Troubleshooting 202 LED Indicator Meanings 202 Symptoms and Solutions 203 8 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 9
Table of Contents Relationship between Aspect and Screen Aspect 209 Displayed Test Patterns 213 Supported Signal Types........... 214 Product Specifications 216 Index 224 Option 227 Menu Configuration 228 Table of Contents 9 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 10
again, check operations and cable connections, and try the solutions in the "Troubleshooting" section in the back of this manual. If the problem still persists, contact the Canon Customer Support Center. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 11
Safety Instructions Safety Instructions Safety Precautions WARNING: • THIS APPARATUS MUST BE cm (1.6') • Do not cover the ventilation slots on the projector. Heat build-up can reduce the service life of your projector, and can also be dangerous. • If the projector is unused for an extended - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 12
■ READ AND KEEP THIS OWNER'S MANUAL FOR LATER USE. All the safety and operating instructions should be read before beginning to operate the product. Read all of the instructions given here and retain them for later use. Unplug this projector from the AC power supply before cleaning. Do not - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 13
service personnel under the following conditions: a. When the power cord or plug is damaged or frayed. b. If liquid has been spilled into the projector. c. If the projector has been exposed to rain or water. d. If the projector does not operate normally after following the operating instructions - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 14
Safety Instructions AC Power Cord Requirement The AC Power Cord supplied with this projector meets the please contact your local city office, waste authority, approved scheme or your household waste disposal service or visit www.canon-europe.com/weee, or www.canon-europe.com/battery. 14 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 15
limits in Subpart B of Part 15 of FCC Rules. Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment. Canon U.S.A. Inc. One Canon Park, Melville - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 16
Safety Instructions Safety Symbols in this Manual This section describes the safety symbols used in this manual. Important projector safety information is identified by the following symbols. Always observe the safety information by these symbols. Denotes the risk of death or serious - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 17
Safety Instructions Safety Instructions Precautions for Use As this section contains important safety occur, turn the power off, remove the power plug from the power outlet and contact the Canon Customer Support Center. Failure to do so could cause a fire or result in an electric shock. • If smoke - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 18
Safety Instructions Pay attention to the following points regarding the power source, power plug and handling of the connector. Failure to do so may cause a fire, electric - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 19
Instructions Safety Instructions maintenance or repair is required, contact the Canon Customer Support Center. • Do not disassemble or modify the projector stable. • For ceiling mounting precautions, refer to the installation manual included with the ceiling mount (sold separately). • When hanging - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 20
Safety Instructions Precautions on the Lamp This projector uses a high-pressure mercury have ruptured. In this case, never attempt to replace the lamp by yourself. Always request service from the Canon Customer Support Center. • With ceiling-mounted projectors, the lamp may fall out when you open the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 21
Safety Instructions Safety Instructions Precautions for the Batteries of the Remote Control Pay attention to the following points regarding handling of batteries. Failing to do so could result in a - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 22
Safety Instructions Pay attention to the following points regarding installation and handling of the projector. • If the projector will not be used for a long period of time, - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 23
lens unit should not be performed by the user. Be sure to have the procedure performed by a qualified technician or contact the Canon Customer Support Center. • Disconnect the cables connected to the projector. Carrying the projector while the cables are attached may cause an accident. • Retract the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 24
in upward or downward projection. Failure to adjust the settings may shorten the lamp life or damage the lamp. For details, contact the Canon Customer Support Center. • Do not install the projector near high-voltage electrical power lines or an electrical power source. • Do not use the projector on - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 25
PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. NO SUPPORT Canon Inc., and all its subsidiaries or its dealers do not make any support service regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall not respond to any - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 26
26 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 27
Before Use Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 27 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 28
controls are also available (RS-RC05). However, some buttons are not supported with this projector. The RS-RC05 can also be used as a m / 5.9') For Continental Europe • CD-ROM User's Manual / Supplement NMPJ Ver. 1.1 User's Manual For the U.S.A. and Canada • Warranty Card • Important Information - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 29
Before Use Preparing the Remote Control ■ Installing Remote Control Batteries 1 Open the battery compartment lid. Slide the lid while pressing it down. 2 Insert batteries. Insert 2 new AAA batteries in the compartment with the + and - poles positioned correctly. 3 Close the compartment lid. - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 30
Preparing the Remote Control ■ Remote Control Operating Range The remote control is an infrared type. Point it at the infrared remote receiver on the front or rear of the projector to operate it. 25° 8 m (26.3') 25° 8 m (26.3') 25° 25° • Use the remote control within an angle of 25° in any direction - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 31
Before Use Part Names Projector ■ Front Side Power cord connector (P138) Side control (P34) Lens unit Air intake vent Terminals and connectors Infrared remote receiver (P30) Air filter (P196) Do not block the air intake. Doing so may cause a malfunction. Anti-theft lock hole An anti-theft - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 32
Part Names Remote control The projector can be operated using buttons on the remote control or the side control on the main unit. The remote control allows you to operate all functions of the projector. (8) (1) (9) (2) (10) (11) (3) (4) (12) (13) (14) (15) (5) (16) (17) (6) (18) (19) - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 33
Before Use Part Names Press D.SHIFT/KEYSTONE to correct keystone distortion. • Moves the image up, down, left, or right when the screen aspect setting is [16:9 D. image shift] or [4:3 D. image shift] is selected. (P50, P51) • To move the image, use the [ ] / [ ] or the [ ] / [ ] buttons. (5) D. - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 34
Part Names Side control (1) LED indicators (P35) The projector status is shown by the LED indicators (off / lit / flashing). For indicator status, refer to "LED Indicator Displays" (P35). POWER ON STAND BY WARNING LAMP TEMP Green Red Red Orange Red Lights up or flashes under normal conditions. - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 35
Before Use Part Names ■ LED Indicator Displays The LED indicators flash or illuminate to indicate the operating status of the projector. : Off : Lit : Flashing LED indicator POWER ON (green) STAND BY (red) WARNING LAMP (red) (orange) TEMP (red) Operating status Not plugged in. In standby - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 36
both video and audio signals across a single cable. (8) LAN port (P164) Connects the LAN cable (shielded twisted pair). Used to connect the projector to a network. (9) Service port (CONTROL) It is not used during ordinary use. 36 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 37
Projecting an Image Appendix Installation and Maintenance Operation Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 38
Step 1 Turn the Projector On 1 Check the connection between the projector and the computer or AV equipment. (P132 - P135) For instructions on connecting the power cord, refer to "Plugging the Projector In" (P138). 2 Press the POWER button. The [POWER ON] indicator initially flashes green, after - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 39
have not changed the input signal since the last projection. Types of Input Signals The table below shows the relationship among input signals supported by the projector, input terminals and connection cables. Input signal Input terminal Types of connection cables HDMI HDMI cable (not included - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 40
Step 2 Select an Input Signal Selecting an Input Signal 1 Press the INPUT button to display the window shown below. Remote control Projector The currently active input signal is marked with a green circle and enclosed by a orange border. An input signal that is ready for projection is displayed - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 41
Operation Projecting an Image Step 3 Adjust the Image Setting the Display Resolution of the Computer Based on the maximum resolution of the projector, set the display resolution of the computer to the resolution closest to the output signal resolution of the projector. (P214) Maximum resolution - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 42
Step 3 Adjust the Image ■ Windows Vista 1 Open the [Control Panel] from the start menu, then select [Appearance and Personalization] - [Adjust screen resolution] in the [Control Panel Home]. 2 Under [Resolution], use the slider to select the resolution closest to the projector's maximum resolution. - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 43
above operation, adjust [Total dots], [Tracking], [Horizontal position], [Vertical position], [Horizontal pixels] and [Vertical pixels] in [Input signal settings]. (P77, P78) • For the signal types supported by the projector, see the table on page 214. 43 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 44
Step 3 Adjust the Image Focusing, Resizing, or Moving the Image Adjusting Image Focus To adjust the focus, press the FOCUS button on the remote control or the LENS button on the projector. For the projection distances of the lens unit, refer to "Relationship Between Image Size and Projecting - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 45
Operation Projecting an Image Step 3 Adjust the Image Adjusting Image Size The size of the projected image can be adjusted by pressing the ZOOM button on the remote control or the LENS button on the projector. Change the projector installation position if your desired image is too large or too - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 46
Step 3 Adjust the Image Adjusting the Image Position To adjust the screen position up, down, left, or right, press the LENS-SHIFT button on the remote control or the LENS button on the projector. It can change the projected screen to the most suitable position by moving the position of the lens up/ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 47
Operation Projecting an Image Step 3 Adjust the Image ■ Resetting the Position The lens position after movement with the lens shift function is not returned when the power is turned off. To return it to its original position, perform reset. During screen position adjustment, press and hold the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 48
Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen Select an optimum aspect ratio of the projected image (screen aspect) or an optimum screen mode (aspect) according to the aspect ratio of the screen, type of input image signal and so on for the projection to make best use of the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 49
Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen 3 Select [Screen aspect] with the [ ] / [ ] buttons, and then press the OK button. Remote control Projector Operation Projecting an Image 4 Use the [ ] / [ ] buttons to select the desired contents. Remote control Projector 16: - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 50
Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen 16:9 D. image shift Select this when you use a screen with an aspect ratio of 16:9. Keystone correction cannot be performed in this mode. However, it is possible to move the image up / down when projecting level. For details about how - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 51
Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen 4 Use the [ ] / [ ] buttons to move the image up or down. Remote control Projector Operation Projecting an Image [ ] button: Moves the image up. Screen [ ] button: Moves the image down. 5 When the image fits the screen, press - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 52
Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen 4 Use the [ ] / [ ] buttons to move the image. Remote control Projector [ ] button: Moves the image right. Screen [ ] button: Moves the image left. 5 When the image fits the screen, press the OK button. Resetting the Image - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 53
Operation Projecting an Image Step 4 Select an Aspect Ratio (Screen Aspect) Matching the Screen 4:3 The image is projected using an input signal aspect ratio of 4:3. Select this if an image of 4:3 aspect ratio cannot be correctly projected in [Auto] mode. Zoom This cuts the upper/lower or left/ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 54
. Horizontal/vertical keystone correction adjusts image width and height, and corner correction adjusts the image relative to each corner. For instructions on switching between the two types of keystone correction, refer to "Specifying Keystone Correction" (P144). Press the D.SHIFT/KEYSTONE button - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 55
Operation Projecting an Image Step 5 Correct the Image Distortion 2 Press the pointer buttons to adjust the dimensions. Remote control [ ] button: Reduces the dimensions of the upper edge. [ ] button: Reduces the dimensions of the lower edge. Screen [ ] button: Reduces the dimension of the left - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 56
Step 5 Correct the Image Distortion 2 Press the pointer button of the corner for correction, and then press the OK button. Remote control 3 Press the pointer buttons to adjust the corner. Remote control 4 When you have finished correcting, press the OK button. Corner adjustment settings will be - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 57
Operation Projecting an Image Step 6 Select the Image Quality (Image Mode) You can select an image mode to suit the projected image. In each image mode, you can further adjust the brightness, contrast, sharpness, gamma, color adjustment, advanced adjustment, and lamp mode. (P84) Image Modes - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 58
Step 6 Select the Image Quality (Image Mode) ■ Selecting an Image Mode Press the IMAGE button on the remote control to select. The image mode changes each time the IMAGE button is pressed. (The displayed image modes vary depending on the selected input signal.) Remote control You can also select any - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 59
Operation Projecting an Image Step 7 Set Power-Saving Settings Next, complete power-saving settings as needed. The following four settings are available. For details, refer to the page describing each function. • Lamp Mode (P95) Adjust lamp and fan power consumption in the image mode. • Power - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 60
Step 8 Turn the Projector Off 1 Press the POWER button to display the window shown below. Remote control Projector 2 When this window is displayed, press the POWER button again to turn off the power. After you turn the power off, the projector will enter standby mode once it cools down. If you - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 61
Useful Functions Available During a Presentation Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 62
Useful Presentation Functions Temporarily Blacking Out an Image Useful when: • You have finished the presentation. • You want to divert attendees' attention from the screen. Remote control Press the BLANK button to black out the image. Press the BLANK button again to show the image. • You can set - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 63
Operation Useful Functions Available During a Presentation Useful Presentation Functions Adjusting the Volume Useful when: • You want to adjust the volume level of the projector or external speakers. Remote control Press the VOL button. The following screen appears. • You can also adjust the volume - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 64
Useful Presentation Functions Zooming Part of an Image Useful when: • Zooming in on an object such as a small graph during a presentation (up to 12x). • Focusing on the current subject. Remote control Press the + D.ZOOM button to enlarge a part of the image. Press the - D.ZOOM button to reduce - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 65
Operation Useful Functions Available During a Presentation Projecting Images on a USB Flash Drive Images stored on a USB flash drive in the projector can be projected as follows. You can select the images to project, or you can project images automatically, one after another. JPEG images up to - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 66
Projecting Images on a USB Flash Drive 4 Use the pointer buttons to select a file, and then press the OK button to project the image. Remote control Projector Press the [ ] / [ ] buttons to select a file. To view another page, press the [ ] / [ ] buttons (if other pages are available). To - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 67
Operation Useful Functions Available During a Presentation Split-Screen Display Two input images can be projected side by side. This is split-screen display. When you activate split-screen display, the current image is shown on the left side, and the new image is shown at right. You can change the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 68
Split-Screen Display 4 Use the [ ] / [ ] buttons to select [On], and then press the OK button. • A number is displayed in the center of one image area. When the image at left is selected, 1 is displayed on the left, and when the image at right is selected, 2 is displayed on the right. The image - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 69
Operation Useful Functions Available During a Presentation Split-Screen Display Side currently under control (input signal can be switched) Current input signal of side with control rights Current input signal of side without control rights To exit split-screen display, select [Input settings] tab - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 70
70 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 71
Setting Functions from Menus Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 72
Using Menus Use the menus to set the operation of the projector in detail. Menu Configuration The menu screen is divided into 6 tabs as shown below. [Install settings] tab This setting is used when installing the projector. [System settings] tab You can set the operation of the projector. [ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 73
Basic Menu Operations 1 Press the MENU button to display the menu window. Remote control Projector Using Menus 2 Press the [ ] / [ ] buttons to select a tab. Remote control Projector Operation Setting Functions from Menus • If the tab position is not highlighted in orange, press the [ ] / [ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 74
screen (1) Example: Menu position (P149) 1. Select [Menu position]. 2. Press the OK button to display a different screen. 3. Then follow the instruction on the screen. Selecting from a different screen (2) Example: Tracking (P77) 1. Select [Input signal settings]. 2. Press the OK button to display - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 75
Operation Setting Functions from Menus Setting Display Status (Input Settings) Selecting the Aspect > [Input settings] > [Aspect] HDMI Digital PC Component Analog PC LAN USB You can select a projection mode corresponding to the aspect ratio of the image. (P52) • For LAN and USB input, [Auto] - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 76
adjust [Total dots], [Tracking], [Horizontal/Vertical position] and [Horizontal/Vertical pixels] in [Input signal settings]. (P77, P78) • For the signal types supported by the projector, see the table on page 214. Select an input signal corresponding to the resolution of the computer. Press the OK - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 77
Operation Setting Functions from Menus Setting Display Status (Input Settings) Adjusting the Input Signal (Total dots) > [Input settings] > [Input signal settings] > [Total dots] HDMI Digital PC Component Analog PC LAN USB You can adjust the total number of dots in the horizontal direction. - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 78
Setting Display Status (Input Settings) Adjusting the Input Adjusting the Input Signal Signal (Horizontal / Vertical position) (Horizontal / Vertical pixels) > [Input settings] > [Input signal settings] > [Horizontal position] / [Vertical position] HDMI Digital PC Component Analog PC LAN USB - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 79
level is selected automatically in [Auto] mode. (Some AV equipment may not support this.) • If the HDMI output of your AV equipment allows switching between HDMI input level]. For more detailed information, refer to the user's manual for the AV equipment connected to the projector. Auto Selects the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 80
Setting Display Status (Input Settings) Specifying HDMI Overscan > [Input settings] > [HDMI over scan] HDMI Digital PC Component Analog PC LAN USB When projecting images in videos via HDMI, select this setting to trim distorted image edges. Specifying Progressive Processing > [Input settings - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 81
Setting Display Status (Input Settings) • [Film/auto] is the factory default. • Select [Off] when flickers and horizontal lines are noticeable in media that has a lot of fast-moving action. • Not available during split-screen display. Specifying the Slideshow Interval > [Input settings] > [ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 82
Setting Display Status (Input Settings) Specifying SplitScreen Display > [Input settings] > [Split screen] HDMI Digital PC Component Analog PC LAN USB You can project two input images side by side. (P67) Press the OK button to accept your setting and then press the MENU button. The image with - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 83
Adjusting Image Quality (Image Adjustment) Specifying Image Priority in Split-Screen Mode > [Image adjustment] > [Image priority] HDMI Digital PC Component Analog PC LAN USB Some image processing in splitscreen mode is applied to both sides. Here, select which side to use as the primary side, - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 84
Adjusting Image Quality (Image Adjustment) Specifying the Image Mode > [Image adjustment] > [Image mode] HDMI Digital PC Component Analog PC LAN USB You can select an image mode (P57) suitable for the projected image. You can also select it with the IMAGE button on the remote control. (P58) - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 85
Adjusting Image Quality (Image Adjustment) Creating/Saving a User Profile > [Image adjustment] > [Create profile] HDMI Digital PC Component Analog PC LAN USB Up to 5 combinations of image quality settings can be stored. The stored image quality can be selected as an image mode. • The image - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 86
Adjusting Image Quality (Image Adjustment) Adjusting Brightness > [Image adjustment] > [Brightness] HDMI Digital PC Component Analog PC LAN USB You can adjust the brightness of images. Adjusting Contrast > [Image adjustment] > [Contrast] HDMI Digital PC Component Analog PC LAN USB You - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 87
Operation Setting Functions from Menus Adjusting Image Quality (Image Adjustment) Adjusting Sharpness > [Image adjustment] > [Sharpness] HDMI Digital PC Component Analog PC LAN USB You can adjust the sharpness of images. Correcting Gamma > [Image adjustment] > [Gamma] HDMI Digital PC - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 88
Adjusting Image Quality (Image Adjustment) Adjusting Colors > [Image adjustment] > [Color adjustment] HDMI Digital PC Component Analog PC LAN USB You can adjust the color depth and hue of images for each primary color, red, green and blue. The color temperature can also be adjusted. R / G / B - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 89
Operation Setting Functions from Menus Adjusting Image Quality (Image Adjustment) Adjusting to the Ambient Light (Ambient Light) > [Image adjustment] > [Advanced adjustment] > [Ambient light] HDMI Digital PC Component Analog PC LAN USB You can compensate for ambient light on the screen. The [ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 90
Adjusting Image Quality (Image Adjustment) Reducing Image Noise (Random noise reduction) Reducing Image Noise (MPEG noise reduction) > [Image adjustment] > [Advanced adjustment] > [Random noise reduction] HDMI Digital PC Component Analog PC LAN USB > [Image adjustment] > [Advanced adjustment] - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 91
Operation Setting Functions from Menus Adjusting Image Quality (Image Adjustment) Reducing Image Noise (Mosquito noise reduction) > [Image adjustment] > [Advanced adjustment] > [Mosquito noise reduction] HDMI Digital PC Component Analog PC LAN USB You can reduce mosquito noise. Dynamic Gamma - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 92
Adjusting Image Quality (Image Adjustment) Correcting Memory Color > [Image adjustment] > [Advanced adjustment] > [Mem. color correct] HDMI Digital PC Component Analog PC LAN USB Enhances skin tones, blue skies, and greens, so that these colors are more consistent with people's remembered - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 93
Adjusting Image Quality (Image Adjustment) • [Off] is the factory default. • The adjustments you have made are stored as adjusted values for the input signals and image mode of the current projection. • Adjustments are not applied to the displayed menu screen itself. Fine-Tuning Gamma > [Image - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 94
Adjusting Image Quality (Image Adjustment) • The adjustments you have made are stored as adjusted values for the input signals and image mode of the current projection. • For details of gamma correction, refer to page 87. • Adjustment is not applied to the projected menu itself. Perform adjustment - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 95
Adjusting Image Quality (Image Adjustment) Specifying the Lamp Mode > [Image adjustment] > [Lamp mode] HDMI Digital PC Component Analog PC LAN USB Reducing the lamp brightness reduces power consumption and cooling fan noise. Resetting Image Adjustment Settings > [Image adjustment] > [Reset] - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 96
Customizing System Operation (System Settings) Registering User Logos > [System settings] > [User screen settings] > [Logo capture] HDMI Digital PC Component Analog PC LAN USB Registers the current image as a user logo. Registered user logos can be shown when no signal is received, when the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 97
Customizing System Operation (System Settings) No Signal Screen > [System settings] > [User screen settings] > [No signal screen] HDMI Digital PC Component Analog PC LAN USB As the image projected when there is no input signal, you can choose a black, blue, or registered user screen. Screen - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 98
Customizing System Operation (System Settings) Selecting a Logo at Startup > [System settings] > [User screen settings] > [Projector on] HDMI Digital PC Component Analog PC LAN USB You can display a specified logo on the screen from the moment the projector is turned on to the moment it is - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 99
Customizing System Operation (System Settings) Specifying Power Management Duration > [System settings] > [Power management duration] HDMI Digital PC Component Analog PC LAN USB Specify how long before the lamp is turned off or the projector enters standby, depending on the [Power management - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 100
Customizing System Operation (System Settings) Specifying Silence or Operating Tones > [System settings] > [Beep] HDMI Digital PC Component Analog PC LAN USB You can select whether a beep sounds or not when you operate the projector. Specifying Key Repeat Operation > [System settings] > [Key - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 101
Customizing System Operation (System Settings) Locking Projector or Remote Buttons > [System settings] > [Key lock] HDMI Digital PC Component Analog PC LAN USB You can lock the projector to prevent its operation from either the main unit or remote control. To Unlock Key Lock Function Turn off - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 102
Customizing System Operation (System Settings) Assigning a Channel for Remote Control > [System settings] > [Remote control channel] HDMI Digital PC Component Analog PC LAN USB When using multiple projectors at the same time (maximum 4), you can assign a different channel to each remote - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 103
Customizing System Operation (System Settings) Reducing Motion Blur > [System settings] > [Motion blur reduction] HDMI Digital PC Component Analog PC LAN USB Motion blur is blurring that occurs during video playback. Motion blur reduction can make this blurring less noticeable. Selecting a - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 104
Customizing System Operation (System Settings) Requiring a Password for Operation > [System settings] > [Other settings] > [Password settings] HDMI Digital PC Component Analog PC LAN USB Disables the projector unless the correct password is entered. To Cancel the Password • Cancellation on - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 105
Operation Setting Functions from Menus Customizing System Operation (System Settings) Setting a Password > [System settings] > [Other settings] > [Register password] HDMI Digital PC Component Analog PC LAN USB You can register a password for starting projection. Using the Remote Control [Fn] - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 106
Customizing System Operation (System Settings) Selecting Audio Input > [System settings] > [Other settings] > [Audio in terminal select] HDMI Digital PC Component Analog PC LAN USB You can select the audio input terminal to use for each type of input signal. • The factory defaults are as - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 107
Customizing System Operation (System Settings) Restoring Original Gamma Settings > [System settings] > [Other settings] > [Gamma restore] HDMI Digital PC Component Analog PC LAN USB This function is used when changing and turning of the tone characteristics and achromatic color is noticed over - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 108
Customizing System Operation (System Settings) Specifying HDMI Input > [System settings] > [HDMI In] HDMI Digital PC Component Analog PC LAN USB Set the type of equipment which is connected to the HDMI port. Note that to some extent, the [HDMI In] setting determines which image modes are - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 109
Operation Setting Functions from Menus Customizing System Operation (System Settings) Over 3,000 hours Displayed as a green, yellow and red bar. Select [Yes] on the screen for confirmation and press the OK button to reset the lamp counter. Press the MENU button. ■ About the Display of the Lamp - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 110
to the root directory on a USB flash drive. In some cases, it may not be possible to download updates. For details, contact the Canon Customer Support Center. To view the air filter counter, press the OK button when [Air filter counter] is selected. Select [Firmware], press the OK button, and - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 111
Customizing System Operation (System Settings) Resetting to the Default Setting > [System settings] > [Other settings] > [Factory defaults] HDMI Digital PC Component Analog PC LAN USB You can reset the menu item settings and restore the system settings to the factory defaults. - [Create - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 112
Checking Projector Information > [Information] HDMI Digital PC Component Analog PC LAN USB You can check information about the signal types of the images projected and other information. Information shown Item Explanation Model name WUX6000 Input signal Details of the input signal - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 113
Installation Appendix Installation and Maintenance Operation Installation and Maintenance Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 114
the user. Be sure to have the procedure performed by a qualified technician or contact the Canon Customer Support Center. Precautions for Installation Be sure to read "Safety Instructions" and "For Safe Use" (P10 - P23). Also take the following precautions during installation. • Do not strike the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 115
Installation and Maintenance Installation Before Installation ■ Do Not Use in the Following Environments • Locations with excessive humidity, dust, oily smoke or tobacco smoke Optical parts such as lenses or mirrors may become cloudy, reducing image quality. • Near high-voltage power lines or - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 116
545.8'), Adjust the Settings Projector settings must be adjusted when using the projector at altitudes of 2,300 m (7,545.8') or higher. Specifically, refer to instructions for [Fan mode] (P146) in the [Install settings] menu. ■ When Using Mounted on the Ceiling When the projector is used mounted on - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 117
also be adjusted. Specifically, for upward or downward projection, refer to instructions for [Vertical projection] (P147) in the [Install settings] menu Always request installation by a qualified technician or the Canon Customer Support Center. 10° 10° Upward projection: Inclination of the projector - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 118
Installation Procedure Setting Up the Projector ■ Positioning the Projector in Front of the Screen Place the projector in front of the screen. • To avoid keystone distortion, install the projector so that it is at right angles to the screen. • The screen must not be exposed to direct sunlight or - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 119
Option" (P227). For details, refer to the assembly and installation manual provided with the ceiling attachment. Mounting the Projector on the Ceiling You CL08 or RS-CL09) may also be required. Contact the Canon Customer Support Center for more detailed information. • Make sure to use the optional - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 120
an accident or personal injury. • Do not attempt to install or remove the lens unit yourself. Be sure to request this service from a qualified technician or contact the Canon Customer Support Center. • When installing and removing the lens unit, be sure not to touch the surface of the lens with your - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 121
Installation and Maintenance Installation Installation Procedure 2 Loosen the cosmetic panel screw, then slide the cosmetic panel toward the rear to remove it. The cosmetic panel screw is attached to the cosmetic panel and designed to prevent it from falling off. 3 In order to prevent damage, close - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 122
Installation Procedure 5 Then turn the projector back over and remove the sleeve. 6 Referring to the following illustration, insert the lens connector of the lens unit into the front right side of the projector slowly until it contacts the end. At this time, pull out the lens cable shown in the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 123
Installation and Maintenance Installation Installation Procedure 8 Insert the projector lens cable into the connector until a click sound is heard. 9 Reinstall the sleeve, cosmetic panel, and lamp cover in their original positions. When the power is first turned on after the lens unit has been - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 124
Installation Procedure ■ Removing the Lens Unit 1 Perform steps 1 to 5 of "Installing the Lens Unit" (P120 - P122) to remove the sleeve. 2 Disconnect the lens cable from the lens connector. When pulling out (disconnecting) the lens cable, press the buttons on both sides of the lens cable connector - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 125
Installation and Maintenance Installation Installation Procedure Relationship Between Image Size and Projecting Distance The projected image size is determined by the distance between the projector and the screen (projection distance) as well as the zoom. Refer to the following table and decide - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 126
Installation Procedure Projection Distance from Image size (cm) distance optical axis Diagonal Lens unit when 16:10 16:10 16:9 m (feet) when projection 4:3 16:10 is perpendicular to screen (cm) Width Height Width Height Width Height Wide limit Tele limit H1 H2 40 86 54 86 48 72 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 127
Installation and Maintenance Installation Installation Procedure Projection Distance from Image size (cm) distance optical axis Diagonal Lens unit when 16:10 16:10 16:9 m (feet) when projection 4:3 16:10 is perpendicular to screen (cm) Width Height Width Height Width Height Wide limit - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 128
Installation Procedure Projection Distance from Image size (cm) distance optical axis Diagonal Lens unit when 16:10 16:10 16:9 m (feet) when projection 4:3 16:10 is perpendicular to screen (cm) Width Height Width Height Width Height Wide limit Tele limit H1 H2 40 86 54 89 50 81 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 129
The projector includes a lens shift function. Operation of the buttons slides the lens up, down, left, and right, moving the image position. For instructions, refer to "Adjusting the Image Position" (P46). The amount of lens shift is indicated as a percentage relative to the image height and width - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 130
Installation Procedure Area Outside the Lens Shift Range With the Standard Zoom Lens, Long Zoom Lens, Ultra Long Zoom Lens, and Wide Zoom Lens, when the shift exceeds 44% in the upward direction, the amount of available shift in the left / right directions decreases. When the lens is shifted upward - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 131
PC Analog PC-1 (P132, P133) Analog PC-2 Component (P132, P133, P136) AUDIO OUT terminal Amplified speakers (P134, P137) LAN LAN terminal Network (P164) Service Port (It is not used during ordinary use.) USB USB Port USB Flash Drive (P65) Analog PC-1 Digital PC DVI-I IN terminal Computer (P133 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 132
Connection Procedure Connecting a Computer Connect the projector to the computer. A digital connection (P133) is recommended when projecting an image in high quality. When using a computer with an HDMI output terminal, a digital connection (P134) can be made using an HDMI cable. Before connecting - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 133
Installation and Maintenance Installation Connection Procedure • Use a DVI-D-sub 15 cable in which all pins are connected. If the cable is a type in which all pins are not connected, the image may not be correctly displayed. • Use an audio cable without a built-in resistor. Using an audio cable - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 134
Connection Procedure • Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor will reduce the audio volume. • The AUDIO IN terminal can be changed in the Audio in terminal select screen (P106). ■ Connecting with an HDMI cable (Input signal type: [HDMI] P39) - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 135
AV Equipment Connect the projector and AV equipment. The description provided here is one example. For more detailed information, refer to the manual for the connected AV equipment. Before connecting the cables, turn off both the projector and AV equipment. ■ Connecting to Digital Video Output - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 136
Connection Procedure ■ Connecting to Analog Video Output Terminal (Analog Connection) Connecting with a component cable (Input signal type: [Component] P39) Component video signals from AV equipment can be supplied to the projector by connecting the component cable to the projector's COMPONENT - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 137
Connection Procedure ■ Outputting Audio to Speakers It is possible to output audio from the projected images to AV equipment or amplified speakers. Projector Speaker To AUDIO OUT terminal Audio cable (not included) RCA terminal Mini jack AUDIO IN terminal (AUDIO IN) Use an audio cable without - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 138
Connection Procedure Plugging the Projector In Connect the power cord to the projector and plug it in. Connect the ground terminal on the power plug to ground. Not doing so could result in an electric shock. Additionally, it may cause computers to be affected by electromagnetic interference and - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 139
Installation and Maintenance Installation Starting Projection Starting and Stopping Projection ■ Starting Projection Press the POWER button on the remote control or on the projector. The [POWER ON] indicator initially flashes green, after which it remains lit. Remote control Projector ■ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 140
. • The function key you use and the method used to turn on the external monitor output vary depending on the model. For details, see the manual for your notebook computer. • With Windows 8.1, Windows 8 or Windows 7, you can turn on image output by holding down the Windows logo key and pressing the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 141
Installation-Related Menu Settings Locking Installation Settings > [Install settings] > [Positional lock] HDMI Digital PC Component Analog PC LAN USB Operation of installation related functions can be prohibited. Flipping Image Display > [Install settings] > [Image flip H/V] HDMI Digital PC - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 142
. (P48) Rear projection Rear, Ceiling Mounting • To hang the projector from the ceiling, use the optional bracket. Contact the Canon Customer Support Center for more detailed information. • If you flip the image, the keystone distortion adjustment will be reset. Perform the adjustment again. 16 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 143
Installation and Maintenance Installation Installation-Related Menu Settings Press the OK button to accept your setting and then press the MENU button. • [16:10] is the factory default. • Changing the screen aspect will reset any keystone or digital image shift setting. • [Auto] may be - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 144
Installation-Related Menu Settings • [Zoom] is not available when the following features are used. - Horizontal/vertical keystone correction (P54) - Split-screen mode (P67) • Using [Zoom] after specifying corner adjustment (P55) will clear corner adjustment settings and apply the zoom setting. - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 145
Specifying Digital Image Shift > [Install settings] > [Digital image shift] HDMI Digital PC Component Analog PC LAN USB Moves the position of the projected image. Installation-Related Menu Settings Specifying Micro Digital Image Shift > [Install settings] > [Professional settings] > [Micro- - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 146
Installation-Related Menu Settings Adjusting Image Registration Specifying the Fan Mode > [Install settings] > [Professional settings] > [Registration] HDMI Digital PC Component Analog PC LAN USB Adjusts colors that are out of alignment. You can adjust red, green and blue registration - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 147
Installation-Related Menu Settings Specifying Vertical Projection Saving and Restoring Lens Positions > [Install settings] > [Professional settings] > [Vertical projection] HDMI Digital PC Component Analog PC LAN USB You can ensure adequate cooling by switching the fan mode to suit upward- or - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 148
Installation-Related Menu Settings • To lock (protect) the saved position, set [Positional lock] (P141) to [On]. • [Load position] is not available unless you perform [Save position] once. • The values of the following settings are saved in addition to the lens position information: - Horizontal/ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 149
then press the MENU button. Press the OK button to accept your setting and then press the MENU button. • The factory default is [On]. • The guide screen is shown at the following times. - When no input signal can be detected. (P140) - When an invalid button is pressed in the [BLANK], [FREEZE - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 150
Installation-Related Menu Settings Showing/Hiding Input Showing/Hiding Status Overheat Warnings > [Install settings] > [On screen] > [Show input status] HDMI Digital PC Component Analog PC LAN USB You can select whether the signal status is displayed on the screen when there is no signal or - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 151
Installation-Related Menu Settings Specifying the Menu Display Time > [Install settings] > [On screen] > [Menu display time] HDMI Digital PC Component Analog PC LAN USB The setting for the menu display time can be extended from the normal 10 or 30 seconds to 3 minutes. Showing/Hiding Lamp - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 152
Installation-Related Menu Settings Showing/Hiding Filter Showing/Hiding Split- Cleaning Warnings Screen ID > [Install settings] > [On screen] > [Air filter warning display] HDMI Digital PC Component Analog PC LAN USB A message advising you to perform cleaning can be set to display when the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 153
Installation and Maintenance Installation Installation-Related Menu Settings Displaying Test Patterns > [Install settings] > [Test pattern] HDMI Digital PC Component Analog PC LAN USB You can project a test pattern (P213) to check resolution, color, and other details even without supplying an - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 154
PC LAN USB Overlapping edges of images from multiple projectors used together can be blended to make the overall image more seamless. ■ Basic Instructions Follow these steps when using two projectors side by side. • To simplify adjustment, use the same lens shift position and image mode (ideally - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 155
Installation and Maintenance Installation Installation-Related Menu Settings Here, you can use the following settings in the edge blending menu. Off Adjust Side Left, Width Right, Top, Start Bottom position Color Off blending Adjust adjustment Black level Off adjustment Adjust Marker - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 156
Installation-Related Menu Settings 5 Use the remote control's [ ] button to select [Start position], and use the [ ] / [ ] buttons to move the marker to the right edge where the images overlap. 6 Use the remote control's [ ] button to select [Width], and use the [ ] / [ ] buttons to move the marker - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 157
this overlapping area appear less distracting by performing [Color blending adjustment]. 1 On the edge blending screen of step 2 in "Basic Instructions" (P154), select [Color blending adjustment] > [Adjust]. The color blending adjustment window is displayed. Here, you can use the following settings - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 158
toward the center of the image) is called area "D." Normally, three areas are identified in the context of end markers: A, B, and C. In the following instructions, only area D is adjusted, and the widths of A, B, and C are left at the default value of 0. To prepare for adjustment, set [No signal - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 159
Installation-Related Menu Settings Here, you can use the following settings in the edge blending menu. Black level adjustment Adjust the black level of non-overlapping image areas. Off Adjust Adjustment Black type level D-area base Adjust the area D black level. D-area red Adjust the red - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 160
to the projected image (on all edges), you must adjust the width of areas A, B, and C. In this example, instructions are given for adjusting area B. 1 In the window of step 2 in "Advanced Instructions: Black Level Adjustment" (P158), select [Adjustment type] > [Area] > [Side] > [Right]. 160 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 161
the green component of the area B black level. B-area blue Adjust the blue component of the area B black level. For adjustment instructions, see "Advanced Instructions: Black Level Adjustment" (P158), step 3. Results of adjusting the black level of area B are applied to all sides. 4 Fine-tune the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 162
162 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 163
Connecting to a Network Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 163 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 164
check that the projector IP address does not overlap with other computers that are on the same LAN. To set a projector IP address, follow the instructions in "Completing Computer Settings" (P173) and use the web screen, or use projector TCP/IP settings. (P169) • When you connect the computer to the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 165
Completing Projector Settings From the projector menus screen, network settings can be configured in the [Network Setting] tab. For instructions on menu operations, refer to "Using Menus". (P72) Locking/Unlocking Network Settings > [Network Settings] > [Network settings lock] You can lock/unlock - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 166
Completing Projector Settings Forcibly canceling the network lock On the Network password input screen, press the buttons in the following order to unlock the settings: [ ] [OK] [ ] [OK] [ ] [OK]. This will reset the network password to Specifying the Network Password > [Network settings] > [ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 167
Installation and Maintenance Connecting to a Network Registering a Network Password > [Network settings] > [Register network password] Register the projector network password. Completing Projector Settings Specifying Standby Power Consumption > [Network settings] > [Network standby settings] - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 168
Completing Projector Settings Specifying the Network Function > [Network settings] > [Network function] You can turn the projector network function on or off. Power can be saved by turning the function [Off]. Off Disables the network function. On Enables the network function. Press the OK button to - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 169
Installation and Maintenance Connecting to a Network Specifying DHCP > [Network settings] > [Detailed settings] > [DHCP] You can enable or disable the DHCP function of the projector. Completing Projector Settings Specifying TCP/IP Settings > [Network settings] > [Detailed settings] > [TCP/IP - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 170
conforms to Class 1 as defined in the PJLink standards of the JBMIA (Japan Business Machine and Information System Industries Association). This projector supports all commands that are defined by PJLink Class 1, and has been verified as conforming to the PJLink standard Class 1 definition. • For - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 171
Installation and Maintenance Connecting to a Network What is PJLink? In September 2003, the PJLink Working Group was established under the Data Projector Committee. During the first year, this PJLink Working Group standardized PJLink as a new interface specification for projectors. PJLink is a - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 172
settings] > [Crestron RoomView] Crestron RoomView enables centralized management of multiple projectors over a network. For example, projectors can be remotely controlled to troubleshoot issues, check the useful life of lamps, or turn the projectors on or off. Specify whether or not to use Crestron - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 173
Installation and Maintenance Connecting to a Network Completing Computer Settings Specifying an IP Address Following is an explanation of how to set the PC IP address for each operating system. ■ Windows 8 1 Right-click on the start screen background and click [All Apps] in the lower right. • - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 174
Completing Computer Settings Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 8 When finished, click the [OK] button, and then click the [Close] button in the [Ethernet Properties] window to close it. ■ Windows 7 1 From the PC [Start] menu, select [Control Panel]. 2 Click on [Network and - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 175
Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 Completing Computer Settings Installation and Maintenance Connecting to a Network 7 When the settings are completed, click the [OK] button and then click the [OK] button on the [Local Area Connection Properties] window to close it. ■ - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 176
Completing Computer Settings Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 7 When the settings are completed, click the [OK] button and then click the [OK] button on the [Local Area Connection Properties] window to close it. ■ Mac OS X 1 Open the Apple Menu and select [System - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 177
Installation and Maintenance Connecting to a Network Example IP address: 192.168.254.1 Subnet mask: 255.255.255.0 Completing Computer Settings 5 Click [Apply] to close the network preference window. ■ Resetting the IP Address Setting of the Computer Follow the same procedure as for changing the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 178
power supply Faulty lens connector Unknown error * For details on downloading the Networked Multi-Projection (NMPJ) application, refer to the separate user's manual. The factory default IP address is "192.168.254.254". If DHCP settings are used, ask the network administrator for the projector IP - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 179
Installation and Maintenance Connecting to a Network Completing Computer Settings The projector settings screen is displayed in the web browser. To operate the projector from the computer, click [Projector control]. (P191) ■ Network Setting 1 To access the settings screen, click [Settings] on the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 180
Completing Computer Settings 3 A confirmation window appears. Check the contents and if they are correct, click [Apply]. The settings are applied to the projector. Selecting [Network] or [Password] in the menu will cause this message to be displayed: "Save completed. Please change setting and - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 181
Item User name New password Confirm new password Completing Computer Settings Explanation When logging into the web screen, enter the user name in 1-byte alphanumeric characters and symbols (4 15 characters). When logging into the web screen, enter the password in 1-byte alphanumeric characters - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 182
). For confirmation, enter the same password as you entered in [Password]. For details on Networked Multi-Projection (NMPJ), refer to the separate user's manual. 182 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 183
Completing Computer Settings Setting Up Email [Mail] From [Mail] in the settings screen, you can set the items necessary to send error mails and test mails. For the setting procedure, refer to "Network Setting" (P179). Installation and Maintenance Connecting to a Network Item To: Cc: From: SMTP - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 184
Completing Computer Settings Mail Authentication Settings [Mail auth] From [Mail auth] in the settings screen, you can configure the settings for authentication of mail that is sent when an error occurs. For the setting procedure, refer to "Network Setting" (P179). Item Mail authentication User - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 185
Completing Computer Settings Sending a Test Mail [Send test mail] From [Send test mail] in the settings screen, you can send a test mail to the mail address that was set in [Mail]. The settings cannot be changed from this screen. Item To: Cc: From: Subject: Explanation The recipient address which - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 186
Completing Computer Settings SNMP Item Receive community Password Confirm password Explanation Select the SNMP function version. If OFF is selected, the SNMP function will be turned off and the other settings in this screen cannot be changed. Enter the community name which will receive - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 187
Installation and Maintenance Connecting to a Network Completing Computer Settings Setting PJLink [PJLink] From [PJLink] in the settings screen, you can set the PJLink functions which are the standard for projector management on a network. For the setting procedure, refer to "Network Setting" (P179 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 188
when sending a test mail. Failed to connect to the POP3 server attempting to send a test mail. An authentication type was set which is not supported by the server. Authentication failed attempting to send a test mail. Sending of test mail failed due to a connection failure with the SMTP server or - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 189
The temperature inside the projector is too high for some reason or the outside air temperature is higher than the specified one. If the problem is inside the projector, check whether the projector is installed and operated normally, turn off the projector to cool its inside, and retry projection - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 190
lens connector Error name Text Error name Text Faulty power supply The voltage of part of the power supply is abnormally high or any other problem has occurred in the power supply. Contact your dealer. Faulty lens connector The lens cable is not connected to the lens unit. Check whether the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 191
Installation and Maintenance Connecting to a Network Completing Computer Settings Control via the Web Screen When the projector is connected to a network, it is possible to control the projector from a computer via the network. 1 Turn on the computer and projector. 2 Launch a web browser, enter " - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 192
Completing Computer Settings Item Explanation Projector name The name of the connected projector is displayed. (P186) Comment Shows notes, such as where the projector is installed. (P186) Refresh Refreshes the displayed contents with the most recent information. Power Turns projector power - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 193
Maintenance Appendix Installation and Maintenance Operation Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 193 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 194
cleaning liquid or benzine, as these may damage the finish of the projector. • When using a chemical dust cloth, make sure to read the instructions thoroughly. • When cleaning the projector's lens, use a commonly available air blower or lens cleaning paper. The lens surface is easily damaged, so do - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 195
message is no longer displayed. • This screen is not displayed when [Air filter warning display] is set to [Off]. (P152) Reset the air filter counter manually. (P110) 195 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 196
air filter will not work properly. • When the lamp is replaced, it is recommended that you also replace the air filter. • Contact the Canon Customer Support Center for further information. • Replacement air filter part no.: RS-FL01 • This can also be purchased from the Canon website. 196 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 197
Installation and Maintenance Maintenance Replacing the Lamp When the usage time of the lamp exceeds a certain amount of time, the following message (two types) is displayed for 10 seconds every time the projector is turned on. 2,700 hours to less than 3,000 hours Prepare a new lamp when this screen - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 198
to replace the lamp by yourself. Always request service from the Canon Customer Support Center. Additionally, with ceiling-mounted projectors, the lamp If a lamp ruptures, contact the Canon Customer Support Center and follow the instructions in "Precautions when replacing lamps that stop working - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 199
Installation and Maintenance Maintenance Replacing the Lamp Replacing the Lamp 1 Turn off the projector power and remove the power plug. 2 Loosen one screw and open the lamp cover in the direction of the arrow. The lamp cover screw is attached to the lamp cover and designed to prevent it from - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 200
Replacing the Lamp 7 Select [Reset] > [Yes] to reset the lamp counter. • It is recommended that you also replace the air filter when you replace the lamp. • Contact the Canon Customer Support Center for further information. • Replacement air filter part no.: RS-FL01 200 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 201
Appendix Appendix Installation and Maintenance Operation Appendix Table of Contents Safety Instructions Before Use Projecting an Image Useful Functions Available During a Presentation Setting Functions from Menus Installation Connecting to a Network Maintenance Other Information Index 201 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 202
Troubleshooting LED Indicator Meanings When there is a problem with the projector, the LED same warning occurs again, there may be a malfunction in the projector. Contact the Canon Customer Support Center. WARNING and Faulty lamp LAMP are lit. The lamp does not illuminate. Turn the power - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 203
Troubleshooting LED indicator status WARNING (only) flashes 5 times repeatedly. WARNING (only) flashes not installed. Check whether or not the air filter is installed correctly. Contact the Canon Customer Support Center if the same warning occurs again. The lens cable is not connected to the lens - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 204
Troubleshooting and then plug the projector in again. Contact the Canon Customer Support Center if the same warning occurs again. Check whether the air filter has been selected. No image is projected due to a problem with the computer. Countermeasure Check whether the projector is connected - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 205
Troubleshooting Cause The external monitor output is not set on the notebook this operation varies depending on the model of notebook computer. For more detailed information, refer to the manual that came with your computer. Check whether the dual screen (multi-display) mode is selected on the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 206
Troubleshooting ■ The Projected Image Is Blurred Cause The image is out of focus. The distance to the screen is too short. The projector is not placed - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 207
Troubleshooting ■ You Cannot Project an Image Appropriately Cause The filter is clogged, clean or replace the air filter. (P196) If the lamp has ruptured, follow the instructions in "Precautions when replacing lamps that stop working" (P20). Check whether the operating temperature is between 0°C - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 208
Troubleshooting ■ You Cannot Operate the Remote Control Cause Batteries are not installed properly or they have run out. You are operating the remote control from the - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 209
Relationship between Aspect and Screen Aspect This section describes the relationship between screen aspect (P48) and aspect (P52). Select an optimum aspect ratio of the projected image (screen aspect) or an optimum screen mode (aspect) according to the aspect ratio of the screen, type of input - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 210
Relationship between Aspect and Screen Aspect ■ When the image is projected on a 16:9 screen Aspect ratio of connected device (16:10) 1920 x 1200 1440 x 900 1280 x 800 (16:9) 1920 x 1080 1280 x 720 (4:3) 1600 x 1200 1400 x 1050 640 x 480 Screen aspect setting (P48) [16:9] [16:9 D. image shift] - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 211
Relationship between Aspect and Screen Aspect ■ When projecting on a 16:10 screen in the aspect ratio of the connected device Aspect ratio of connected device (16:10) 1920 x 1200 1440 x 900 1280 x 800 Screen aspect setting (P48) Aspect setting (P52) [16:10] [Auto] Screen image (16:9) 1920 x - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 212
Relationship between Aspect and Screen Aspect ■ When projecting on a 4:3 screen in the aspect ratio of the connected device Aspect ratio of connected device (16:10) 1920 x 1200 1440 x 900 1280 x 800 Screen aspect setting (P48) Aspect setting (P52) [Auto] Screen image (16:9) 1920 x 1080 1280 x - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 213
to switch pattern. A dialog box is shown during test pattern display that identifies the current test pattern and provides operating instructions. The following test patterns can be displayed. Use [ ] / [ ] to switch patterns Use [ ] / [ ] to switch option patterns (1) Color bars (2) Stairstep - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 214
Signal Types This projector supports the following signal types. If your computer or AV equipment is compatible with any one of these signal types, the projector's Auto PC function selects - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 215
Supported Signal Types Resolution (dots) Signal type 1080PsF (1920 x 1080i) - 1920 x 1200 * The specifications in the table above are subject to change without notice. * This projector does not support any computer output signal with a dot clock of higher than 162 MHz. * Use a computer cable - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 216
Product Specifications Projection lens (*1) Display device ■ Projector Model name Display system WUX6000 RGB liquid crystal system Optical system Color separation by dichroic mirror / polarizing beam splitter and color composition by prism Type Size / Aspect ratio Drive system Reflective - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 217
projection lens unit) Accessories Remote control, remote control dry-cell batteries, power cord, PC cable, User's Manual (this manual), Supplement NMPJ Ver. 1.1 User's Manual (CD-ROM), Important Information and Warranty Card *1 When using a Standard Zoom Lens (RS-IL01ST). Varies depending - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 218
Product Specifications ■ Specification of Each Lens Unit (Option) Name Standard Zoom Lens Long Zoom Lens Model number RS-IL01ST RS-IL02LZ External View Focal length F number Width Height Length Weight Zoom ratio Projection distance Size 100 projection distance 23.0 - 34.5 mm (0.9 - 1.4'') - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 219
Name Model number Short Fixed Lens RS-IL03WF Product Specifications Ultra Long Zoom Lens RS-IL04UL External View Focal length F number Width Height Length Weight Zoom ratio Projection distance Size 100 projection distance Name Model number 12.8 mm (0.5'') 2.0 97.4 mm (3.8'') 106.5 mm (4.2'') - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 220
Product Specifications ■ External View WUX6000 91 mm (3.6') 170 mm (6.7') 92 mm (3.6') 430 mm (16.9') 380 mm (15.0') Bolt holes (M4 x 6) for installation of ceiling attachment 128 mm (5.0') 234.5 mm (9.2') 53 mm (2.1') 212 mm (8.35') 150 mm (5.9') 141.5 mm (5.6') 154.5 mm (6.1') 311 mm (12 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 221
Pin No. Signal 9 +5 V power 10 Ground (Vertical sync.) 11 Ground 12 DDC data 13 Horizontal sync. 14 Vertical sync. 15 DDC clock ■ Service Port (CONTROL) Pin assignment Pin No. Signal 1 OPEN 2 RxD 3 TxD 4 OPEN 5 GND 6 OPEN 7 Internal pull-up 8 OPEN 9 OPEN Communication format - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 222
Product Specifications Control commands Commands Power on Power supply Power off Power status acquisition HDMI Digital PC Analog PC-1 Input source Analog PC-2 Component LAN USB Input source acquisition Standard Presentation VividPhoto Photo/sRGB Dynamic Video Image Mode Cinema User 1 User 2 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 223
Product Specifications Commands ASCII representation Brightness acquisition GET=BRI Sharpness Sharpness value setting SHARP= Sharpness acquisition GET=SHARP Contrast Contrast value setting CONT= Contrast acquisition GET=CONT Auto ASPECT=AUTO 4:3 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 224
39, 133 DVI-I 132, 133 DVI-I input terminal 36 Dynamic gamma 91 E Edge blending 154 Electronic zoom 143 F Factory defaults 111 FREEZE 62 G Gamma 87 Guide 149 H HDMI 39, 134, 135 HDMI color space 79 HDMI IN terminal 36, 134, 135 HDMI input level 79 HDMI over scan 80 Horizontal pixels - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 225
Index Image flip H/V (Ceiling mounted / Rear projection 141 Image mode (Image quality 57 Information 72, 112 INPUT 40 Input signal select 39 Input terminal 36 Connecting to AV equipment ......... 135 Connection to computer 132 K Key lock 101 KEYSTONE 54 Keystone 54 L Lamp counter 108 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 226
Index T TCP/IP settings 169 Test pattern 153, 213 Total dots 77 Tracking 77 True size (Aspect 53 Turning on external monitor output (preparing the notebook computer 140 U USB 65 USB Port 36 V Vertical pixels 78 Vertical position 78 VOL 63 W WARNING indicator 34, 202 Z Zooming an Image - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 227
• Remote control Part No.: RS-RC05 * Use the above materials to hang the projector from the ceiling. For details, refer to the assembly and installation manual provided with the ceiling attachment RS-CL11. 227 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 228
Menu Configuration Input Settings Menu *: Factory defaults (setting after reset) Aspect Digital PC / Analog PC-1/2 / HDMI (when [HDMI In] is [Computer]) P75 Auto* 16:10 16:9 4:3 True size HDMI (when [HDMI In] is [Auto]) / Component Auto* 16:9 4:3 Zoom True size USB / LAN Auto Auto - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 229
Slideshow interval Split screen Off* On Settings Menu Configuration USB P81 [--:--] : [60:00] Digital PC / Analog PC-1/2 / HDMI / Component / LAN / USB P82 Split screen Control rights Swap right-left Layout Off On Left screen Right screen Mode 3-7 Mode 5-5 Mode 7-3 Image Adjustment Menu - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 230
Menu Configuration Advanced adjustment Ambient light (when Photo/sRGB is selected) Random noise reduction MPEG noise reduction Off* P89 Adjust Type Tungsten Fluorescent Level L H Digital PC / Analog PC-1/2 / HDMI / Component P90 Off* Weak Middle Strong Digital PC / Analog PC-1/2 / HDMI / - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 231
Install Settings Menu Positional lock Image flip H/V Screen aspect Zoom (Short Fixed Lens) Keystone Digital image shift Professional settings Micro-digital image shift Registration Fan mode Vertical projection Edge Blending Menu Configuration Off* On None* Ceiling mounted Rear Rear, Ceiling - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 232
Menu Configuration Lens - Position Screen color On screen Menu position Guide Show input status Overheat warning display Menu display time Lamp warning display Air filter warning display Split screen ID display Test pattern System Settings Menu - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 233
Power management mode Power management duration Direct power on Beep Key repeat Key lock Remote control channel Motion blur reduction Language Other settings Password settings Register password [Fn] button settings Menu Configuration Disabled Lamp off Standby* 5 min. 10 min. 15 min.* 20 min. 30 - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 234
Menu Configuration Audio in terminal select HDMI Digital PC Analog PC-1 Analog PC-2 Component LAN USB Gamma restore HDMI In Lamp counter Air filter counter Firmware Factory defaults Network Settings Menu Network settings lock Network password setting Register network password Network standby - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 235
Network function Detailed settings IP address Gateway address MAC address DHCP TCP/IP settings Network setting initialization PJLink AMX Device Discovery Crestron RoomView Information Model name Input signal Firmware Serial no. IP address E-mail sender address E-mail recipient address Projector name - Canon REALiS LCOS WUX6000 | MULTIMEDIA PROJECTOR WUX6000 Users Manual - Page 236
CANON INC. 30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan U.S.A. CANON U.S.A. INC. One Canon Park, Melville, New York 11747, U.S.A. For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON CANADA CANON CANADA INC. HEADQUARTERS 6390 Dixie Road, Mississauga,
Table of Contents
Safety Instructions
Before Use
Operation
Projecting an Image
Useful Functions Available
During a Presentation
Setting Functions from
Menus
Installation and Maintenance
Installation
Connecting to a Network
Maintenance
Appendix
Other Information
Index
ENG
MULTIMEDIA PROJECTOR
User’s Manual