Canon i900D i900D Direct Printing Guide - Page 46

Cannot Print Properly from the Digital Camera

Get Canon i900D PDF manuals and user guides View all Canon i900D manuals
Add to My Manuals
Save this manual to your list of manuals

Page 46 highlights

„ Cannot Print Properly from the Digital Camera The following messages may be displayed on the cameras or camcorders when images are printed directly. Take the appropriate action to correct the error. This section describes errors that can occur when you connect a Canon "Bubble Jet Direct" compatible digital camera to the printer. • Images can be printed directly from a "PictBridge" or Canon "Bubble Jet Direct" compatible digital cameras and digital video camcorders connected to this printer. • If the connected digital camera or digital video camcorder is not supported by this printer, the Power lamp on the printer will flash nine times. If this happens, disconnect the connection cable and press the Resume button. • If the operation time or data transmission time is too long, a communication time error may occur and no more images can be printed. If this error occurs, disconnect the camera connection cable, press the Resume button and then connect the cable once again. The digital camera should be turned on automatically. If not, turn it on manually. • A low ink warning is not displayed on the digital camera. • For more details, also refer to the user's manual for the digital camera or digital video camcorder. Error message on camera Printer in use Printer warming up No Paper Paper Jam Printer cover open No print head Waste tank full Printer error Try This Images are printed from the computer. Wait until printing ends. Wait until warm-up ends. Load the paper in the printer and press the Resume button on the printer. Remove the jammed paper, load new media, and press the Resume button. Close the front cover. The Power lamp on the printer flashes five times. No print head is installed. Install a print head according to the Quick Start Guide. When there is a print head installed, the print head is defective. Contact a Canon service representative. The waste ink tank is nearly full. Press the Resume button on the printer to recover from the error. Contact a Canon service representative as soon as possible. An error requiring servicing has occurred. (The Power lamp on the printer flashes alternately orange and green.) Turn off the printer, unplug the power cord from the power supply, plug the power cord back in, and then turn on the printer. If the same error occurs, contact a Canon service representative. 45

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
45
Cannot Print Properly from the Digital Camera
The following messages may be displayed on the cameras or camcorders when images are printed
directly. Take the appropriate action to correct the error.
This section describes errors that can occur when you connect a Canon “Bubble Jet Direct” compatible
digital camera to the printer.
•
Images can be printed directly from a “PictBridge” or Canon “Bubble Jet Direct” compatible
digital cameras and digital video camcorders connected to this printer.
•
If the connected digital camera or digital video camcorder is not supported by this printer, the
Power
lamp on the printer will flash nine times. If this happens, disconnect the connection cable
and press the
Resume
button.
•
If the operation time or data transmission time is too long, a communication time error may occur
and no more images can be printed. If this error occurs, disconnect the camera connection cable,
press the
Resume
button and then connect the cable once again.
The digital camera should be turned on automatically. If not, turn it on manually.
•
A low ink warning is not displayed on the digital camera.
•
For more details, also refer to the user’s manual for the digital camera or digital video camcorder.
Error message on
camera
Try This
Printer in use
Images are printed from the computer.
Wait until printing ends.
Printer warming up
Wait until warm-up ends.
No Paper
Load the paper in the printer and press the
Resume
button on the
printer.
Paper Jam
Remove the jammed paper, load new media, and press the
Resume
button.
Printer cover open
Close the front cover.
No print head
The
Power
lamp on the printer flashes five times.
No print head is installed. Install a print head according to the Quick
Start Guide.
When there is a print head installed, the print head is defective.
Contact a Canon service representative.
Waste tank full
The waste ink tank is nearly full.
Press the
Resume
button on the printer to recover from the error.
Contact a Canon service representative as soon as possible.
Printer error
An error requiring servicing has occurred. (The
Power
lamp on the
printer flashes alternately orange and green.)
Turn off the printer, unplug the power cord from the power supply, plug
the power cord back in, and then turn on the printer. If the same error
occurs, contact a Canon service representative.