Canon imageFORMULA P-150 Portable Scanner User Manual - Page 60

Resetting the Counters, Click [Start], [All Programs], [Canon P-150], and then click

Get Canon imageFORMULA P-150 Portable Scanner PDF manuals and user guides View all Canon imageFORMULA P-150 Portable Scanner manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Resetting the Counters Make sure to reset the scanner's internal counters using the following procedure whenever you replace the feed roller and separation pad. IMPORTANT This section describes the procedure to use when the Auto Start switch on the rear panel of the scanner is set to the "OFF" position. If the Auto Start switch is set to the "ON" position (when you only use CaptureOnTouch Lite and have not installed CaptureOnTouch and the scanner driver on your computer), you cannot reset the counter using this procedure. In this case, you can reset the counter from CaptureOnTouch Lite. For details, see page 31. 1 Start Windows and log on as a user with administrator privileges. 2 Set the switch at the rear of the scanner to OFF. 3 Connect the scanner to the computer. 4 Open the feed tray to turn the scanner ON. 5 Click [Start], [All Programs], [Canon P-150], and then click [Utility]. The Canon imageFORMULA utility starts. 8 Click [Reset] for both [Current Rollers] and [Current Pad]. The counter for [Current Rollers] and [Current Pad] resets. 9 Click [OK] to close the scanner properties. 6 Select [Canon P-150 USB], and click [Properties]. The scanner's properties appear. 7 Click the [Maintenance] tab. 60

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
60
Resetting the Counters
Make sure to reset the scanner’s internal counters using the following
procedure whenever you replace the feed roller and separation pad.
IMPORTANT
This section describes the procedure to use when the Auto Start
switch on the rear panel of the scanner is set to the “OFF” position.
If the Auto Start switch is set to the “ON” position (when you only use
CaptureOnTouch Lite and have not installed CaptureOnTouch and
the scanner driver on your computer), you cannot reset the counter
using this procedure. In this case, you can reset the counter from
CaptureOnTouch Lite. For details,
see page 31
.
1
Start Windows and log on as a user with administrator
privileges.
2
Set the switch at the rear of the scanner to OFF.
3
Connect the scanner to the computer.
4
Open the feed tray to turn the scanner ON.
5
Click [Start], [All Programs], [Canon P-150], and then click
[Utility].
The Canon imageFORMULA utility starts.
6
Select [Canon P-150 USB], and click [Properties].
The scanner’s properties appear.
7
Click the [Maintenance] tab.
8
Click [Reset] for both [Current Rollers] and [Current Pad].
The counter for [Current Rollers] and [Current Pad] resets.
9
Click [OK] to close the scanner properties.