Chamberlain RJO20 RJO20 Owner s Manual - English

Chamberlain RJO20 Manual

Get Chamberlain RJO20 PDF manuals and user guides View all Chamberlain RJO20 manuals
Add to My Manuals
Save this manual to your list of manuals

Chamberlain RJO20 manual content summary:

  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 1
    ! • Fasten the manual near the garage door after installation. • The door WILL NOT CLOSE unless the Protector System® and cable tension monitor are connected and properly aligned. • Periodic checks of the garage door opener are required to ensure safe operation. • This garage door opener is ONLY
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 2
    Preparation Safety Symbol and Signal Word Review This garage door opener has been designed and tested to offer safe service provided it is installed, operated, maintained, and tested in strict accordance with the instructions and warnings contained in this manual. Mechanical When you see these
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 3
    you may encounter as you prepare and install your garage door opener. Term Bearing Plate Cable Tension Monitor Door Seal Drum Extension Springs High Lift Sectional Door Roller Safety Reversing Sensor Torsion Springs Torsion Bar Definition Acts as a support for the torsion bar. The bearing and
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 4
    . The outlet must be 120 VAC - 60 Hz ONLY. Contact a qualified electrician if you need an outlet installed. Previously installed garage door opener has been removed completely. Ceiling Distance between ceiling and torsion bar is 3" (7.6 cm) or more Torsion bar must extend at least 1-1/2 inches
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 5
    locks and remove ALL ropes connected to garage door BEFORE installing and operating garage door opener to avoid entanglement. To prevent damage to garage door and opener: • ALWAYS disable locks BEFORE installing and operating the opener. • ONLY operate garage door opener at 120 V, 60 Hz to avoid
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 6
    installation and adjustment is complete. The images throughout this manual are for reference only and your product may look different. Collar with Set Screws Mounting Bracket Garage Door Opener Sensor Bracket (2) Chamberlain Internet Gateway ACCESSORIES White & White/Red Wire Door Control (myQ®
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 7
    mounting of the safety reversing sensor will require hardware not provided. •  Extension brackets (Model 041A5281-1) or wood blocks and shimming material. - Used to position the garage door opener during installation and for testing the safety reversing sensors if
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 8
    . 7. NEVER connect garage door opener to power source until instructed to do so. 8. NEVER wear watches, rings or loose clothing while installing or servicing the garage door opener. They could be caught in door or operator mechanisms. 9. Install wall-mounted door control: • within sight
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 9
    Attach the Collar to the Garage Door Opener The garage door opener can be installed on either side of the door; see "Is Your Garage Ready?" on page 4. The illustrations shown are for installation on the left side. 1. Loosen the preset collar screws with the 3/8" open end wrench. 2. Slide the collar
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 10
    Mount the Garage Door Opener 1. Close the garage door completely. 
 2. Slide the garage door opener onto the end of the torsion bar. 
Ensure the collar does NOT touch the bearing plate. 3. Use a level to align the garage door opener parallel to the door. Verify the mounting bracket installation wall
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 11
    screws 1/4 - no more than 1/2 turn after making contact with the shaft. If installing on a keyed torsion bar, DO NOT tighten the screws into the keyway. 9. Secure the mounting bracket to the wall and to the garage door opener. Use the 14‑10x2" screws to secure the mounting bracket to the wall. Set
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 12
    Location 1. Determine where to install the power door lock. • Mount the door lock on the same side as the opener. The third roller from the floor is ideal for most installations. • The power door lock MUST be mounted within 10 feet (3.05 m) of garage door opener with approximately a 3 inch (7.6 cm
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 13
    monitor detects any slack in the garage door cables. When slack is detected, the garage door opener stops the door from closing, and reverses the door to stay open. The cable tension monitor MUST be connected and properly installed BEFORE the garage door opener will move in the down direction
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 14
    Lag Screw 5/16"-9x2" Screw 1/4-20 (2) #8 Hex Head Screw (2) Installation (continued) 7 Attach the Cable Tension Monitor 1. Mark and drill is on top of the cable. 
 3. Run wire to garage door opener. Securely affix wire to wall and ceiling. Secure any additional wire away from the moving parts of
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 15
    in sight until completely closed. NEVER permit anyone to cross path of closing garage door. YOU WILL NEED Screw 6ABx1-1/4" (Standard installation) (2) Drywall Anchors (2) Screw 6-32x1" (pre-wired) (2) (to garage door opener) Push bar 6 7/16" (11 mm) 1 10 To insert or release wire, push in tab
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 16
    (continued) IMPORTANT INSTALLATION INSTRUCTIONS To reduce the risk of SEVERE INJURY or DEATH: 1. Light is intended for ceiling mount and indoor applications ONLY. 9 Install Remote Light HARDWARE The remote light (garage door opener light) is designed to plug directly into a standard 120V outlet
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 17
    beam path must be unobstructed. No part of the garage door (door tracks, springs, hinges, rollers or other hardware) may interrupt the beam while the door is closing. Be sure power is NOT connected to the garage door opener BEFORE installing the safety reversing sensor. To prevent SERIOUS INJURY or
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 18
    safety reversing sensors will face each other across the garage door, with the beam no higher than 6" (15 cm) above the floor. Be sure power to the opener is disconnected. Choose one of the following installations. OPTION A: Track Installation (Recommended) 1. Slip the curved arms over the rounded
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 19
    Installation (continued) MOUNTING THE SAFETY REVERSING SENSORS 1. Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor. 2. Use wing nuts to fasten safety reversing sensors to brackets, with lenses pointing toward each other across the door . 3. On the garage door opener, push the tab
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 20
    (continued) WRWORNOGNG PERPMERAMNAENTENWTIRWIINRGING COCNONNECNTEICOTNION 11 Connect Power To avoid installation difficulties, do not run the garage door opener at this time. To reduce the risk of electric shock, your garage door opener has a grounding type plug with a third grounding pin. This
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 21
    steadily: • Check that both sensors are installed inside the garage, one on either side of the door. • Check that sensors are facing each above the floor. Amber LED is not lit: • Check there is power to the garage door opener. 
 • Check the sensor wire is not shorted/broken. 
 • Check the sensor
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 22
    (open) position. LED Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • NEVER learn forces or limits when door is binding or sticking. Repair door first. • Incorrect adjustment of garage door
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 23
    door will open (UP). Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. • NEVER learn forces or limits when door is binding or sticking. Repair door first. • Too much force on garage door will
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 24
    or force controls. • Any repair to or adjustment of the garage door (including springs and hardware). • Any repair to or buckling of the garage floor. • Any repair to or adjustment of the opener. Without a properly installed safety reversal system, persons (particularly small children) could be
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 25
    by sliding the manual release handle to the open position. However, if the power door lock does not function, contact Chamberlain for a replacement. PPoowwereDroDoroLoorckLock MMaannuaulaRleRleaesleease To prevent possible SERIOUS INJURY or DEATH from a falling garage door: • If possible, use
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 26
    . 14. SAVE THESE INSTRUCTIONS. Using Your Garage Door Opener Your garage door opener has already been programmed at the factory to operate with your remote control, which changes with each use, randomly accessing over 100 billion new codes. When programmed to the Chamberlain® Internet Gateway you
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 27
    control panel will beep and the garage door opener lights will flash before closing the door. The TTC feature will deactivate if the garage door encounters an obstruction twice; or the safety reversing sensors are incorrectly installed. The garage door will reverse open and WILL NOT close until the
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 28
    the garage door opener lights turn on, then off again.* * Approximately 10 seconds Using the Remote Control Press and hold the button down until the door or gate starts to move. The remote control will operate from up to 3 car lengths away on typical installations. Installations and conditions
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 29
    the home and allows you to close an open garage door from inside the house. LEARN Button Model WSLCEV - Remote Light Switch Light module can be synchronized with the garage door opener light bulbs. *myQ® accessories may be programmed to the Chamberlain® Internet Gateway (Model 828LG) or the myQ
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 30
    when the remote light comes on. HomeLink® In the rare case the HomeLink system does not program with the Security+ 2.0 Garage door opener, install a repeater kit. Refer to HomeLink instructions below. HomeLink is the in-vehicle system. The image used is for reference only and your product may look
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 31
    serial number located on the garage door opener Figure 1 Router Green LED Power Chamberlain Internet Gateway Connect the instructions given in the app to find and connect your Internet Gateway. 3. Next, select the device you wish to add (Garage Door Opener). 4. Once you select the opener
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 32
    Maintenance Care of Your Garage Door Opener MAINTENANCE SCHEDULE Once a Month • Manually operate door. If it is unbalanced or binding, call a trained door systems technician. • Check to be sure door opens and closes fully. Adjust limits and/or force if necessary (see Adjustment Steps 1 and 2). • 
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 33
    Troubleshooting Diagnostic Chart Your garage door opener is programmed with selfdiagnostic capabilities. The diagnostic LED will flash a number of times, then pause, signifying it has found a potential issue. Consult Diagnostic Chart below. Installed Safety Reversing Sensor Installed Safety
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 34
    control: • Does the garage door opener have electric power? Plug a lamp into the outlet. If it doesn't light, check the fuse box or the circuit breaker. (Some outlets are controlled by a wall switch.) • Have you disabled all door locks? Review installation instruction warnings on page 7. • Is
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 35
    ) Troubleshooting (Continued) The garage door opener motor hums briefly, then won't work: • The garage door springs may be broken. See above. • If the problem occurs on the first operation of the garage door opener, door may be locked. Disable the power door lock. The garage door opener won
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 36
    Please review the safety and maintenance tips in this guide carefully and keep it for reference. Check the operation of your garage door and opener to ensure they function in a safe and trouble-free manner. Be sure to read all Important Safety Information found in your garage door opener's manual as
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 37
    garage door and opener system a part of your regular routine. Review your owner's manual for both the door and door opener. If you don't have the owner's manuals the door and installation: • Starting with the door in the closed position, use the manual disconnect on the opener to disconnect the door.
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 38
    from their car computer and allows with their garage you to monitor and control garage door opener remote door openers and lighting accessories or from anywhere LOCK enabled by myQ® technology. in their home with an additional Chamberlain® remote. SEND PASS READY ENROLL ENROLL FAIL RETRY
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 39
    TRANSMITTERS AND LIGHT BULBS), OR UNITS INSTALLED FOR NON-RESIDENTIAL USE. THIS LIMITED WARRANTY DOES NOT COVER ANY PROBLEMS WITH, OR RELATING TO, THE GARAGE DOOR OR GARAGE DOOR HARDWARE, INCLUDING BUT NOT LIMITED TO THE DOOR SPRINGS, DOOR ROLLERS, DOOR ALIGNMENT OR HINGES. THIS LIMITED WARRANTY
  • Chamberlain RJO20 | RJO20 Owner s Manual - English - Page 40
    AZ 85706 For installation and service information call: 1-800-528-9131 Or visit us online at: www.chamberlain.com BEFORE YOU CALL: 1. Please have the model number of the garage door opener, found on the inside cover of door panel or front page of this manual. 2. For a troubleshooting issue, have
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
•
Please read this manual and the enclosed safety materials carefully!
•
Fasten the manual near the garage door after installation.
•
The door WILL NOT CLOSE unless the Protector System
®
and cable tension
monitor are connected and properly aligned.
•
Periodic checks of the garage door opener are required to ensure safe operation.
•
This garage door opener is ONLY compatible with myQ
®
accessories.
•
The model number label is located behind the hinged door of your opener.
This product is NOT intended for use on low headroom tracks with outside pickup
drum or garage doors utilizing extension springs. For advanced or customized
adjustments, door springs, and/ or track configurations, contact a trained door
systems technician.
For Residential Use
Install On Sectional Doors With Torsion Assemblies Only
Wall Mount Garage Door Opener
Model RJO20
The Chamberlain Group, Inc.
300 Windsor Drive
Oak Brook, IL 60523