Cisco 7206 Installation Guide - Page 100

Configuring Interfaces

Get Cisco 7206 - VXR Router PDF manuals and user guides
UPC - 746320703879
View all Cisco 7206 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 100 highlights

Configuring the Cisco 7206 Chapter 4 Performing a Basic Configuration of the Cisco 7206 The following sample display includes a continuous listing of all configuration parameters selected in Step 3 through Step 9. These parameters are shown in the order in which they appear on your console terminal. Only IP, IPX, and AppleTalk are the selected protocols for this example. Configuring global parameters: Enter host name [Router]: router The enable secret is a one-way cryptographic secret used instead of the enable password when it exists. Enter enable secret: barney The enable password is used when there is no enable secret and when using older software and some boot images. Enter enable password: betty Enter virtual terminal password: fred Configure SNMP Network Management? [yes]: Community string [public]: Configure IP? [yes]: Configure IGRP routing? [yes]: Your IGRP autonomous system number [1]: 15 Configure Vines? [no]: Configure IPX? [no]: y Configure AppleTalk? [no]: y Multizone networks? [no]: y Configure Apollo? [no]: Configure DECnet? [no]: Configure XNS? [no]: Configure CLNS? [no]: Configure bridging? [no]: Step 10 Save your settings to NVRAM. (Refer to the "Saving Your Settings to NVRAM" section on page 4-10.) Configuring Interfaces Following are the steps for configuring interfaces to allow communication over a LAN or WAN. To configure the interface parameters, you need your interface network addresses and subnet mask information. Consult with your network administrator for this information. Configuring Ethernet Interfaces In the following example, the system is being configured for an Ethernet LAN using IP. Step 1 Step 2 Respond to the prompts as follows, using your own addresses and mask at the setup prompts: Configuring interface parameters: Configuring interface Ethernet0/0: Is this interface in use? [yes]: Use the 100 Base-TX (RJ-45) connector? [yes]: Configure IP on this interface? [no]: yes IP address for this interface: 10.1.1.10 Number of bits in subnet field [0]: Class A network is 1.0.0.0, 0 subnet bits; mask is 255.0.0.0 Determine if you are going to enable IPX on this interface; if you are, enter the unique IPX network number: Cisco 7206 Installation and Configuration Guide 4-6 OL-5102-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
4-6
Cisco 7206 Installation and Configuration Guide
OL-5102-02
Chapter 4
Performing a Basic Configuration of the Cisco 7206
Configuring the Cisco 7206
The following sample display includes a continuous listing of all configuration parameters selected in
Step 3
through
Step 9
. These parameters are shown in the order in which they appear on your console
terminal. Only IP, IPX, and AppleTalk are the selected protocols for this example.
Configuring global parameters:
Enter host name [Router]:
router
The enable secret is a one-way cryptographic secret used
instead of the enable password when it exists.
Enter enable secret:
barney
The enable password is used when there is no enable secret
and when using older software and some boot images.
Enter enable password:
betty
Enter virtual terminal password:
fred
Configure SNMP Network Management? [yes]:
Community string [public]:
Configure IP? [yes]:
Configure IGRP routing? [yes]:
Your IGRP autonomous system number [1]: 15
Configure Vines? [no]:
Configure IPX? [no]: y
Configure AppleTalk? [no]: y
Multizone networks? [no]: y
Configure Apollo? [no]:
Configure DECnet? [no]:
Configure XNS? [no]:
Configure CLNS? [no]:
Configure bridging? [no]:
Step 10
Save your settings to NVRAM. (Refer to the
“Saving Your Settings to NVRAM” section on page 4-10
.)
Configuring Interfaces
Following are the steps for configuring interfaces to allow communication over a LAN or WAN. To
configure the interface parameters, you need your interface network addresses and subnet mask
information. Consult with your network administrator for this information.
Configuring Ethernet Interfaces
In the following example, the system is being configured for an Ethernet LAN using IP.
Step 1
Respond to the prompts as follows, using your own addresses and mask at the setup prompts:
Configuring interface parameters:
Configuring interface Ethernet0/0:
Is this interface in use? [yes]:
Use the 100 Base-TX (RJ-45) connector? [yes]:
Configure IP on this interface? [no]:
yes
IP address for this interface:
10.1.1.10
Number of bits in subnet field [0]:
Class A network is 1.0.0.0, 0 subnet bits; mask is 255.0.0.0
Step 2
Determine if you are going to enable IPX on this interface; if you are, enter the unique IPX network
number: