Cisco ASR1004-20G-SEC/K9 Software Guide - Page 260
Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide, OL-16506-10, Configuring Call Home, Message Contents
View all Cisco ASR1004-20G-SEC/K9 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 260 highlights
Message Contents Chapter 7 Configuring Call Home filtering disabled Exception Logging: size (4096 bytes) Count and timestamp logging messages: disabled Persistent logging: disabled No active filter modules. Trap logging: level informational, 104 message lines logged Log Buffer (1000000 bytes): *Dec 3 07:16:55.020: ASR1000-RP HA: RF status CID 1340, seq 93, status RF_STATUS_REDUNDANCY_MODE_CHANGE, op 0, state DISABLED, peer DISABLED *Dec 3 07:17:00.379: %ASR1000_MGMTVRF-6-CREATE_SUCCESS_INFO: Management vrf Mgmt-intf created with ID 4085, ipv4 table-id 0xFF5, ipv6 table-id 0x1E000001 *Dec 3 07:17:00.398: %NETCLK-5-NETCLK_MODE_CHANGE: Network clock source not available. The network clock has changed to freerun *Dec 3 07:17:00.544: %LINEPROTO-5-UPDOWN: Line protocol on Interface LI-Null0, changed state to up *Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface EOBC0, changed state to up *Dec 3 07:17:00.545: %LINK-3-UPDOWN: Interface Lsmpi0, changed state to up *Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface LIIN0, changed state to up *Dec 3 07:17:00.546: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to down *Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface EOBC0, changed state to up *Dec 3 07:17:01.557: %LINEPROTO-5-UPDOWN: Line protocol on Interface Lsmpi0, changed state to up *Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface LIIN0, changed state to up *Dec 3 07:17:01.558: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down *Dec 3 07:17:01.818: %DYNCMD-7-CMDSET_LOADED: The Dynamic Command set has been loaded from the Shell Manager *Dec 3 07:16:30.926: %CMRP-5-PRERELEASE_HARDWARE: R0/0: cmand: 2 is pre-release hardware *Dec 3 07:16:24.147: %HW_IDPROM_ENVMON-3-HW_IDPROM_CHECKSUM_INVALID: F1: cman_fp: The idprom contains an invalid checksum in a sensor entry. Expected: 63, calculated: fe *Dec 3 07:16:24.176: %CMFP-3-IDPROM_SENSOR: F1: cman_fp: One or more sensor fields from the idprom failed to parse properly because Success. *Dec 3 07:16:27.669: %CPPHA-7-START: F1: cpp_ha: CPP 0 preparing image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:27.839: %CPPHA-7-START: F1: cpp_ha: CPP 0 startup init image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:28.659: %CPPHA-7-START: F0: cpp_ha: CPP 0 preparing image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:28.799: %CPPHA-7-START: F0: cpp_ha: CPP 0 startup init image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:32.557: %CPPHA-7-START: F1: cpp_ha: CPP 0 running init image /tmp/sw/fp/1/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:32.812: %CPPHA-7-READY: F1: cpp_ha: CPP 0 loading and initialization complete *Dec 3 07:16:33.532: %CPPHA-7-START: F0: cpp_ha: CPP 0 running init image /tmp/sw/fp/0/0/fp/mount/usr/cpp/bin/cpp-mcplo-ucode *Dec 3 07:16:33.786: %CPPHA-7-READY: F0: cpp_ha: CPP 0 loading and initialization complete *Dec 3 07:16:34.158: %IOSXE-6-PLATFORM: F1: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Dec 3 07:16:35.134: %IOSXE-6-PLATFORM: F0: cpp_cp: Process CPP_PFILTER_EA_EVENT__API_CALL__REGISTER *Dec 3 07:16:38.965: %CMRP-6-FP_HA_STATUS: R0/0: cmand: F0 redundancy state is Active with ready Standby *Dec 3 07:17:01.926: %DYNCMD-7-PKGINT_INSTALLED: The command package 'platform_trace' has been succesfully installed 7-44 Cisco ASR 1000 Series Aggregation Services Routers Software Configuration Guide OL-16506-10