Cisco WS-X6148-GE-TX Hardware Installation Guide - Page 60

Installing a Power Supply, Removing the Power Supply for the Cisco UCS 6120XP

Get Cisco WS-X6148-GE-TX - Switch PDF manuals and user guides
UPC - 746320802060
View all Cisco WS-X6148-GE-TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Replacing or Installing Components Chapter 2 Installing the Cisco UCS 6100 Series Fabric Interconnect Send document comments to [email protected] Step 3 Push against the release latch with your left thumb and slide the power supply out of the chassis. See Figure 2-14 or Figure 2-15. Figure 2-14 Removing the Power Supply for the Cisco UCS 6120XP Figure 2-15 Removing the Power Supply for the Cisco UCS 6140XP 273163 Step 4 Step 5 Place your right hand under the power supply to support it while you slide it out of the chassis. If you are not replacing the power supply, install a blank power supply filler panel (N10-S1BLKP= or N10-S2BLKP=). If you are replacing the power supply, see Installing a Power Supply, page 2-26. Installing a Power Supply To install a power supply, follow these steps: Step 1 Ensure that the system (earth) ground connection has been made. For ground connection instructions, see the "Grounding the System" section on page 2-11. 2-26 Cisco UCS 6100 Series Fabric Interconnect Hardware Installation Guide OL-20036-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Send document comments to [email protected]
2-26
Cisco UCS 6100 Series Fabric Interconnect Hardware Installation Guide
OL-20036-02
Chapter 2
Installing the Cisco UCS 6100 Series Fabric Interconnect
Replacing or Installing Components
Step 3
Push against the release latch with your left thumb and slide the power supply out of the chassis. See
Figure 2-14
or
Figure 2-15
.
Figure 2-14
Removing the Power Supply for the Cisco UCS 6120XP
Figure 2-15
Removing the Power Supply for the Cisco UCS 6140XP
Step 4
Place your right hand under the power supply to support it while you slide it out of the chassis.
Step 5
If you are not replacing the power supply, install a blank power supply filler panel (N10-S1BLKP= or
N10-S2BLKP=). If you are replacing the power supply, see
Installing a Power Supply, page 2-26
.
Installing a Power Supply
To install a power supply, follow these steps:
Step 1
Ensure that the system (earth) ground connection has been made. For ground connection instructions,
see the
“Grounding the System” section on page 2-11
.
273163