Cisco WS-X6148-GE-TX Hardware Installation Guide - Page 74

Maintaining SFP Transceivers and Fiber-Optic Cables

Get Cisco WS-X6148-GE-TX - Switch PDF manuals and user guides
UPC - 746320802060
View all Cisco WS-X6148-GE-TX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Connecting to a Fibre Channel Port Chapter 3 Connecting the Cisco UCS 6100 Series Fabric Interconnect Send document comments to [email protected] Caution If the cable does not remove easily, ensure that any latch present on the cable has been released before continuing. To remove the cable, follow these steps: Step 1 Step 2 Step 3 Step 4 Attach an ESD wrist strap and follow its instructions for use. Press the release latch on the cable, grasp the connector near the connection point, and gently pull the connector from the transceiver. Insert a dust plug into the cable end of the transceiver. Insert a dust plug onto the end of the cable. Maintaining SFP Transceivers and Fiber-Optic Cables SFP transceivers and fiber-optic cables must be kept clean and dust-free to maintain high signal accuracy and prevent damage to the connectors. Attenuation (loss of light) is increased by contamination and should be below 0.35 dB. Consider the following maintenance guidelines: • SFP transceivers are static sensitive. To prevent ESD damage, wear an ESD wrist strap that is connected to the chassis. • Do not remove and insert a transceiver more often than is necessary. Repeated removals and installation can shorten its useful life. • Keep all optical connections covered when not in use. If they become dusty, clean before using to prevent dust from scratching the fiber-optic cable ends. • Do not touch ends of connectors to prevent fingerprints and other contamination. • Clean regularly; the required frequency of cleaning depends upon the environment. In addition, clean connectors if they are exposed to dust or accidentally touched. Both wet and dry cleaning techniques can be effective; refer to fiber-optic cleaning procedures for your site. • Inspect routinely for dust and damage. If damage is suspected, clean and then inspect fiber ends under a microscope to determine if damage has occurred. 3-10 Cisco UCS 6100 Series Fabric Interconnect Hardware Installation Guide OL-20036-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
Send document comments to [email protected]
3-10
Cisco UCS 6100 Series Fabric Interconnect Hardware Installation Guide
OL-20036-02
Chapter 3
Connecting the Cisco UCS 6100 Series Fabric Interconnect
Connecting to a Fibre Channel Port
Caution
If the cable does not remove easily, ensure that any latch present on the cable has been released before
continuing.
To remove the cable, follow these steps:
Step 1
Attach an ESD wrist strap and follow its instructions for use.
Step 2
Press the release latch on the cable, grasp the connector near the connection point, and gently pull the
connector from the transceiver.
Step 3
Insert a dust plug into the cable end of the transceiver.
Step 4
Insert a dust plug onto the end of the cable.
Maintaining SFP Transceivers and Fiber-Optic Cables
SFP transceivers and fiber-optic cables must be kept clean and dust-free to maintain high signal accuracy
and prevent damage to the connectors. Attenuation (loss of light) is increased by contamination and
should be below 0.35 dB.
Consider the following maintenance guidelines:
•
SFP transceivers are static sensitive. To prevent ESD damage, wear an ESD wrist strap that is
connected to the chassis.
•
Do not remove and insert a transceiver more often than is necessary. Repeated removals and
installation can shorten its useful life.
•
Keep all optical connections covered when not in use. If they become dusty, clean before using to
prevent dust from scratching the fiber-optic cable ends.
•
Do not touch ends of connectors to prevent fingerprints and other contamination.
•
Clean regularly; the required frequency of cleaning depends upon the environment. In addition,
clean connectors if they are exposed to dust or accidentally touched. Both wet and dry cleaning
techniques can be effective; refer to fiber-optic cleaning procedures for your site.
•
Inspect routinely for dust and damage. If damage is suspected, clean and then inspect fiber ends
under a microscope to determine if damage has occurred.