Cuisinart SS-10P1 User Manual - Page 13

Stopping the Brew, Process, Adding Water, Programming

Get Cuisinart SS-10P1 PDF manuals and user guides View all Cuisinart SS-10P1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Stopping the Brew Process If for any reason you need to stop brewing after the process has started, press the BREW button, OR press the power switch on the rear right side of the coffeemaker to turn the coffeemaker off. The flow of coffee, tea or hot cocoa will stop, the heater will shut off, and the blue lights illuminating the control panel will turn off. Note: You may get less coffee, tea or hot cocoa in your cup during your next brew. In order for your next brew to be the volume you have selected, we recommend that you perform a rinse cycle after a terminated brew. Programming Setting the Clock Setting the clock is optional. When the clock is set, the time will appear on the control panel. Note: You must set the clock if you plan on using the ON OFF TIME SET programming feature. 1. Press the Menu button. Programming options will appear on the control panel with CLOCK flashing. The word OFF will appear at the top of the control panel to indicate that the clock is not set (see figure 14). Adding Water The control panel will indicate when the water level in your reservoir is low or if the reservoir has been removed by displaying the words "ADD WATER." When "ADD WATER" is displayed, the coffeemaker will not allow you to brew. The Water Reservoir can be filled in two ways: 1. Lift off the reservoir lid and pour water directly into the reservoir while it is still attached to the coffeemaker, then replace the lid. 2. Remove the reservoir from coffeemaker by first removing the lid from the reservoir, then lifting the reservoir straight up and away from the coffeemaker. Fill with water, place the reservoir back on the coffeemaker, and replace the lid. IMPORTANT: Do not remove the water reservoir during the brewing process. Note: If your coffeemaker has not been used for more than one week, we suggest running a rinse cycle before next brew. Set Minutes Set Hours figure 14 2. Press or hold the button to scroll through the hours until you have reached the appropriate hour. Be sure the PM indicator is on if a PM time is desired. 3. Press or hold the button to scroll through the minutes until you have reached the desired minutes. 4. When you have reached the correct time, press the Menu button to set the time. Continue pressing Menu to scroll through the remaining programming functions to exit the Programming mode. 5. The correct time should now be displayed on top of the control panel (see figure 15). 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
13
Stopping the Brew
Process
If for any reason you need to stop brewing
after the process has started, press the
BREW button,
OR
press the power switch
on the rear right side of the coffeemaker to
turn the coffeemaker off. The flow of coffee,
tea or hot cocoa will stop, the heater will
shut off, and the blue lights illuminating the
control panel will turn off.
Note:
You may get less coffee, tea or hot
cocoa in your cup during your next brew.
In order for your next brew to be the volume
you have selected, we recommend that you
perform a rinse cycle after a terminated brew.
Adding Water
The control panel will indicate when the
water level in your reservoir is low or if the
reservoir has been removed by displaying
the words “ADD WATER.” When “ADD
WATER” is displayed, the coffeemaker will
not allow you to brew.
The Water Reservoir can be filled in
two ways:
1. Lift off the reservoir lid and pour water
directly into the reservoir while it is still
attached to the coffeemaker, then
replace the lid.
2. Remove the reservoir from coffeemaker
by first removing the lid from the reservoir,
then lifting the reservoir straight up and
away from the coffeemaker. Fill with
water, place the reservoir back on the
coffeemaker, and replace the lid.
IMPORTANT:
Do not remove the water
reservoir during the brewing process.
Note:
If your coffeemaker has not been
used for more than one week, we suggest
running a rinse cycle before next brew.
Programming
Setting the Clock
Setting the clock is optional. When the clock
is set, the time will appear on the control
panel.
Note:
You must set the clock if you
plan on using the ON OFF TIME SET
programming feature.
1. Press the Menu button. Programming
options will appear on the control panel
with CLOCK flashing. The word OFF will
appear at the top of the control panel
to indicate that the clock is not set
(see figure 14).
2. Press or hold the
button to scroll
through the hours until you have
reached the appropriate hour. Be sure
the PM indicator is on if a PM time is
desired.
3. Press or hold the
button to scroll
through the minutes until you have
reached the desired minutes.
4. When you have reached the correct
time, press the Menu button to set the
time. Continue pressing Menu to scroll
through the remaining programming
functions to exit the Programming mode.
5. The correct time should now be
displayed on top of the control panel
(see figure 15).
figure 14
Set Hours
Set Minutes