D-Link DCS-934L User Manual - Page 15

Zero Configuration Setup - wireless setup

Page 15 highlights

Section 2 - Installation Zero Configuration Setup The Zero Configuration Setup will only work with a registered Cloud Router and an active mydlink account. Your Cloud Router will automatically assign your camera's network settings (both wired and wireless), and add the camera to your mydlink account. This means you can set up your camera by simply plugging it in and connecting it to your router. After the setup is complete, you can remotely access your camera from the website (http://www.mydlink.com). If you do not have a D-Link Cloud Router, skip to the "Camera Setup Wizard" on page 18. If you prefer, you can skip to "Manual Installation" on page 20. To learn more about mydlink, refer to "What is mydlink?" on page 24. Connect the Power Cable and Ethernet Cable Step 1 Attach the power supply to the power receptor located on the back of the DCS-934L and connect it to a wall outlet or power strip. Power is confirmed when the Power LED is lit. Step 2 If using an Ethernet connection, connect the included Ethernet cable to the Ethernet port located on the back of your camera. Plug the other end into an available port on your D-link Cloud Router. Note: If you later decide to use your camera wirelessly, you will be able to remove the cable after Zero Configuration Setup is complete. If you prefer to initiate a wireless connection with your router, you can use WPS (Wi-Fi Protected Setup). Refer to "WPS - Push Button Setup" on page 21. D-Link DCS-934L User Manual 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72

15
D-Link DCS-934L User Manual
Section 2 - Installation
Zero Configuration Setup
The Zero Configuration Setup will only work with a registered Cloud Router and an active mydlink account. Your Cloud Router
will automatically assign your camera’s network settings (both wired and wireless), and add the camera to your mydlink
account. This means you can set up your camera by simply plugging it in and connecting it to your router. After the setup is
complete, you can remotely access your camera from the website (
).
If you do not have a D-Link Cloud Router, skip to the
“Camera Setup Wizard” on page 18
. If you prefer, you can skip to
”Manual Installation” on page 20
. To learn more about mydlink, refer to
“What is mydlink?” on page 24
.
Connect the Power Cable and Ethernet Cable
Step 1
Attach the power supply to the power receptor located on the back of the DCS-934L and
connect it to a wall outlet or power strip. Power is confirmed when the Power LED is lit.
Step 2
If using an Ethernet connection, connect the included Ethernet cable to the Ethernet port
located on the back of your camera. Plug the other end into an available port on your
D-link Cloud Router.
Note:
If you later decide to use your camera wirelessly, you will be able to remove the cable
after Zero Configuration Setup is complete.
If you prefer to initiate a wireless connection with your router, you can use WPS (Wi-Fi
Protected Setup). Refer to
“WPS - Push Button Setup” on page 21
.