D-Link DES-3552 Product Manual - Page 175

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide

for this rule.

IPv4 Address

– Selecting this option will allow the user to enter a range of IPv4 addresses

for this rule.

IPv6

– Selecting this option will allow the user to enter a range of IPv6 addresses for this

rule.

Action

Select

Permit

to specify that the packets that match the access profile are forwarded by the

Switch, according to any additional rule added (see below).

Select

Deny

to specify that the packets that match the access profile are not forwarded by

the Switch and will be filtered.

Select

Mirror

to specify that packets that match the access profile are mirrored to a port

defined in the mirror port section. Port Mirroring must be enabled and a target port must be

set.

Option

After selecting the Permit

action, the user can select one of the following options:

Change 1p Priority

– Enter the 1p priority value.

Replace DSCP

– Enter the DSCP value.

Replace ToS Precedence

– Enter the ToS Precedence value.

Apply To

Select and enter the object that this rule will be applied to.

Ports

– Enter a port number or a port range.

VLAN Name

– Enter the VLAN name.

VLAN ID

– Enter the VID.

Click the

Apply

button to accept the changes made.

NOTE:

The Switch will use one minimum mask to cover all the terms that user input, however, some extra

bits may also be masked at the same time. To optimize the ACL profile and rules, please use

manual configuration.

Access Profile List

Access profiles allow you to establish criteria to determine whether the Switch will forward packets based on the

information contained in each packet's header.

To view Access Profile List window, click

ACL > Access Profile List

, as shown below:

The Switch supports four Profile Types, Ethernet ACL, IPv4 ACL, IPv6 ACL, and Packet Content ACL.

Creating an access profile is divided into two basic parts. The first is to specify which part or parts of a frame the Switch

will examine, such as the MAC source address or the IP destination address. The second part is entering the criteria

the Switch will use to determine what to do with the frame. The entire process is described below in two parts.

Users can display the currently configured Access Profiles on the Switch.

NOTE:

By default, R2.60 supports only 12 ACL profiles and 1536 rules as compared to support for 14

profiles and 1792 rules in R2.01. As a consequence, some ACL settings in previous configuration

files may be lost after firmware upgrade. To have access to all 14 ACL profiles and 1792 rules,

disable the local routing feature and reload the configuration.

166

Section	Page
Intended Readers	10
Typographical Conventions	10
Notes, Notices and Cautions	10
Chapter 1 Web-based Switch Configuration	11
Introduction	11
Login to the Web Manager	11
Web-based User Interface	12
Web Pages	13
Chapter 2 System Configuration	14
Device Information	14
System Information Settings	15
Dual Configuration Settings	16
Firmware Information Settings	17
Port Configuration	18
PoE	21
Serial Port Settings	24
System Log configuration	25
Time Range Settings	29
Time Settings	29
User Accounts Settings	30
Stacking	31
Chapter 3 Management	35
ARP	35
Gratuitous ARP	37
IPv6 Neighbor Settings	38
IP Interface	39
Management Settings	43
Session Table	44
Single IP Management	44
SNMP Settings	54
Telnet Settings	64
Web Settings	64
Chapter 4 L2 Features	65
VLAN	65
Q-in-Q	88
Layer 2 Protocol Tunneling Settings	90
Spanning Tree	91
Link Aggregation	100
FDB	103
L2 Multicast Control	107
Multicast Filtering	132
ERPS Settings	136
LLDP	139
Chapter 5 L3 Features	149
Local Route Settings	149
IPv4 Static/Default Route Settings	149
IPv4 Route Table	150
IPv6 Static/Default Route Settings	151
IPv6 Route Table	151
Policy Route Settings	152
IP Forwarding Table	153
Chapter 6 QoS	154
802.1p Settings	156
Bandwidth Control	159
Traffic Control Settings	161
DSCP	164
HOL Blocking Prevention	167
Scheduling Settings	168
SRED	171
Chapter 7 ACL	174
ACL Configuration Wizard	174
Access Profile List	175
CPU Access Profile List	193
ACL Finder	207
ACL Flow Meter	208
Chapter 8 Security	211
802.1X	211
RADIUS	224
IP-MAC-Port Binding (IMPB)	229
MAC-based Access Control (MAC)	236
Web-based Access Control (WAC)	240
Japanese Web-based Access Control (JWAC)	245
Compound Authentication	252
Port Security	256
ARP Spoofing Prevention Settings	258
BPDU Attack Protection	259
Loopback Detection Settings	261
Traffic Segmentation Settings	262
NetBIOS Filtering Settings	263
DHCP Server Screening	264
Access Authentication Control	265
SSL Settings	274
SSH	276
Trusted Host Settings	280
Safeguard Engine Settings	281
Chapter 9 Network Application	284
DHCP	284
DNS	296
PPPoE Circuit ID Insertion Settings	298
SNTP	299
Chapter 10 OAM	302
CFM	302
Ethernet OAM	311
DULD Settings	315
Cable Diagnostics	316
Chapter 11 Monitoring	318
Utilization	318
Statistics	320
Mirror	332
sFlow	334
Ping Test	337
Trace Route	338
Peripheral	340
Chapter 12 Save and Tools	341
Save Configuration ID 1	341
Save Configuration ID 2	341
Save Log	342
Save All	342
Stacking Information	342
Download Firmware	344
Download Configuration File	344
Upload Configuration File	345
Upload Log File	346
Reset	347
Reboot System	347
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	348
How Address Resolution Protocol Works	348
How ARP Spoofing Attacks a Network	350
Prevent ARP Spoofing via Packet Content ACL	351
Configuration	351
Appendix B System Log and Trap List	354
System Log Entries	354
DES-3528/DES-3552 Series Trap List	362
Proprietary Trap List	362
Appendix C Password Recovery Procedure	365

D-Link DES-3552 Product Manual - Page 175

Access Profile List, Action, Option, Apply To, Apply, ACL > Access Profile List

Page 175 highlights