D-Link DES-3552 Product Manual - Page 46

xStack® DES-3528/DES-3552 Series Layer 2 Stackable Fast Ethernet Managed Switch Web UI Reference Guide

Upgrade to v1.61

To better improve SIM management, the DES-3528/DES-3552 Series switches have been upgraded to version 1.61 in

this release. Many improvements have been made, including:

1.

The Commander Switch (CS) now has the capability to automatically rediscover member switches that have

left the SIM group, either through a reboot or web malfunction. This feature is accomplished through the use of

Discover packets and Maintenance packets that previously set SIM members will emit after a reboot. Once a

MS has had its MAC address and password saved to the CS’s database, if a reboot occurs in the MS, the CS

will keep this MS information in its database and when a MS has been rediscovered, it will add the MS back

into the SIM tree automatically. No configuration will be necessary to rediscover these switches.

There are some instances where pre-saved MS switches cannot be rediscovered. For example, if the Switch is still

powered down, if it has become the member of another group, or if it has been configured to be a Commander Switch,

the rediscovery process cannot occur.

2.

The topology map now includes new features for connections that are a member of a port trunking group. It will

display the speed and number of Ethernet connections creating this port trunk group, as shown in the adjacent

picture.

3.

This version will support switch upload and downloads for firmware, configuration files and log files, as follows:

a.

Firmware

– The Switch now supports MS firmware downloads from a TFTP server.

b.

Configuration Files

– This switch now supports downloading and uploading of configuration files both to

(for configuration restoration) and from (for configuration backup) MS’s, using a TFTP server.

c.

Log

– The Switch now supports uploading MS log files to a TFTP server.

4.

The user may zoom in and zoom out when utilizing the topology window to get a better, more defined view of

the configurations.

Single IP Settings

The Switch is set as a Candidate (CaS) as the factory default configuration and Single IP Management is disabled.

To view the following window, click

Management > Single IP Management > Single IP Settings

, as shown below:

Figure 3-15 Single IP Settings window

The fields that can be configured are described below:

Parameter

Description

SIM State

Use the pull-down menu to either enable or disable the SIM state on the Switch.

Disabled

will

render all SIM functions on the Switch inoperable.

Role State

Use the pull-down menu to change the SIM role of the Switch. The two choices are:

Candidate

– A Candidate Switch (CaS) is not the member of a SIM group but is connected to

a Commander Switch. This is the default setting for the SIM role of the Switch.

Commander

– Choosing this parameter will make the Switch a Commander Switch (CS). The

user may join other switches to this Switch, over Ethernet, to be part of its SIM group.

Choosing this option will also enable the Switch to be configured for SIM.

37

Section	Page
Intended Readers	10
Typographical Conventions	10
Notes, Notices and Cautions	10
Chapter 1 Web-based Switch Configuration	11
Introduction	11
Login to the Web Manager	11
Web-based User Interface	12
Web Pages	13
Chapter 2 System Configuration	14
Device Information	14
System Information Settings	15
Dual Configuration Settings	16
Firmware Information Settings	17
Port Configuration	18
PoE	21
Serial Port Settings	24
System Log configuration	25
Time Range Settings	29
Time Settings	29
User Accounts Settings	30
Stacking	31
Chapter 3 Management	35
ARP	35
Gratuitous ARP	37
IPv6 Neighbor Settings	38
IP Interface	39
Management Settings	43
Session Table	44
Single IP Management	44
SNMP Settings	54
Telnet Settings	64
Web Settings	64
Chapter 4 L2 Features	65
VLAN	65
Q-in-Q	88
Layer 2 Protocol Tunneling Settings	90
Spanning Tree	91
Link Aggregation	100
FDB	103
L2 Multicast Control	107
Multicast Filtering	132
ERPS Settings	136
LLDP	139
Chapter 5 L3 Features	149
Local Route Settings	149
IPv4 Static/Default Route Settings	149
IPv4 Route Table	150
IPv6 Static/Default Route Settings	151
IPv6 Route Table	151
Policy Route Settings	152
IP Forwarding Table	153
Chapter 6 QoS	154
802.1p Settings	156
Bandwidth Control	159
Traffic Control Settings	161
DSCP	164
HOL Blocking Prevention	167
Scheduling Settings	168
SRED	171
Chapter 7 ACL	174
ACL Configuration Wizard	174
Access Profile List	175
CPU Access Profile List	193
ACL Finder	207
ACL Flow Meter	208
Chapter 8 Security	211
802.1X	211
RADIUS	224
IP-MAC-Port Binding (IMPB)	229
MAC-based Access Control (MAC)	236
Web-based Access Control (WAC)	240
Japanese Web-based Access Control (JWAC)	245
Compound Authentication	252
Port Security	256
ARP Spoofing Prevention Settings	258
BPDU Attack Protection	259
Loopback Detection Settings	261
Traffic Segmentation Settings	262
NetBIOS Filtering Settings	263
DHCP Server Screening	264
Access Authentication Control	265
SSL Settings	274
SSH	276
Trusted Host Settings	280
Safeguard Engine Settings	281
Chapter 9 Network Application	284
DHCP	284
DNS	296
PPPoE Circuit ID Insertion Settings	298
SNTP	299
Chapter 10 OAM	302
CFM	302
Ethernet OAM	311
DULD Settings	315
Cable Diagnostics	316
Chapter 11 Monitoring	318
Utilization	318
Statistics	320
Mirror	332
sFlow	334
Ping Test	337
Trace Route	338
Peripheral	340
Chapter 12 Save and Tools	341
Save Configuration ID 1	341
Save Configuration ID 2	341
Save Log	342
Save All	342
Stacking Information	342
Download Firmware	344
Download Configuration File	344
Upload Configuration File	345
Upload Log File	346
Reset	347
Reboot System	347
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	348
How Address Resolution Protocol Works	348
How ARP Spoofing Attacks a Network	350
Prevent ARP Spoofing via Packet Content ACL	351
Configuration	351
Appendix B System Log and Trap List	354
System Log Entries	354
DES-3528/DES-3552 Series Trap List	362
Proprietary Trap List	362
Appendix C Password Recovery Procedure	365

D-Link DES-3552 Product Manual - Page 46

Single IP Settings, Upgrade to v1.61

Page 46 highlights