D-Link DGS-3130 Quick Install Guide - Page 16

Power, Console, Fan Err, Link/Act LEDs, SFP Ports, 10G RJ45 Ports, SFP+ Ports

Get D-Link DGS-3130 PDF manuals and user guides View all D-Link DGS-3130 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

DGS-3130 Series Layer 3 Stackable Managed Switch Hardware Installation Guide LED Power Console MGMT RPS Fan Err USB Link/Act LEDs Figure 2-6 LED indicators for the DGS-3130-30S Description This LED will light solid green after the Switch has been powered on successfully. This LED will be off when the Switch is no longer receiving power (i.e. powered off). This LED will light solid green when the RJ45 console port is active. This LED will blink when activity on this port is taking place. This LED will be off when console ports are not active. The LED at the left side indicates the status of MGMT port. This LED will light solid green or amber after a link to the MGMT port was successfully established. This LED will blink when activity on this port is taking place. This LED will be off when MGMT port is not active. This LED will light green when the Redundant Powers Supply is in use. This LED will be off when the RPS is not in use. This LED will light solid red when the fan fails. This LED will be off when the fan is operating normally. This LED will light solid green if a USB flash drive is plugged in. This LED will blink green when the Switch is reading or writing data to and from the USB drive. This LED will be off when no USB drive is plugged into the USB port. This LED will light solid red when a USB drive failure has been detected. The Switch has LED indicators for Link and Activity. SFP Ports: The triangle LED indicates the Link/Act status of SFP ports. This LED will light solid green when there is a connection (or link) to a 1000 Mbps Ethernet device or solid amber when there is a connection (or link) to a 100 Mbps Ethernet device on any of the SFP ports. The LED will blink green when a 1000 Mbps port is active or blink amber when a 100 Mbps port is active. The LED will be off when there is no link or activity. 10G RJ45 Ports: The LED at the left side indicates the Link/Act status of upper 10G RJ45 ports. The LED at the right side indicates the Link/Act status of lower 10G RJ45 ports. This LED will light solid green when there is a connection (or link) to a 10 Gbps Ethernet device or solid amber when there is a connection (or link) to a 100/1000 Mbps Ethernet device on any of the RJ45 ports. The LED will blink green when a 10 Gbps port is active or blink amber when a 100/1000 Mbps port is active. The LED will be off when there is no link or activity. SFP+ Ports: The triangle LED indicates the Link/Act status of 10G SFP+ ports. This LED will light solid green when there is a connection (or link) to a 10 Gbps Ethernet device or solid amber when there is a connection (or link) to a 1 Gbps Ethernet device at any at any of the SFP+ ports. The LED will blink green 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
DGS-3130 Series Layer 3 Stackable Managed Switch Hardware Installation Guide
16
Figure 2-6 LED indicators for the DGS-3130-30S
LED
Description
Power
This LED will light solid green after the Switch has been powered on
successfully.
This LED will be off when the Switch is no longer receiving power (i.e. powered
off).
Console
This LED will light solid green when the RJ45 console port is active.
This LED will blink when activity on this port is taking place.
This LED will be off when console ports are not active.
MGMT
The LED at the left side indicates the status of MGMT port.
This LED will light solid green or amber after a link to the MGMT port was
successfully established.
This LED will blink when activity on this port is taking place.
This LED will be off when MGMT port is not active.
RPS
This LED will light green when the Redundant Powers Supply is in use.
This LED will be off when the RPS is not in use.
Fan Err
This LED will light solid red when the fan fails.
This LED will be off when the fan is operating normally.
USB
This LED will light solid green if a USB flash drive is plugged in.
This LED will blink green when the Switch is reading or writing data to and from
the USB drive.
This LED will be off when no USB drive is plugged into the USB port.
This LED will light solid red when a USB drive failure has been detected.
Link/Act LEDs
The Switch has LED indicators for Link and Activity.
SFP Ports:
The triangle LED indicates the Link/Act status of SFP ports. This
LED will light solid green when there is a connection (or link) to a 1000 Mbps
Ethernet device or solid amber when there is a connection (or link) to a 100
Mbps Ethernet device on any of the SFP ports. The LED will blink green when
a 1000 Mbps port is active or blink amber when a 100 Mbps port is active. The
LED will be off when there is no link or activity.
10G RJ45 Ports:
The LED at the left side indicates the Link/Act status of
upper 10G RJ45 ports. The LED at the right side indicates the Link/Act status
of lower 10G RJ45 ports. This LED will light solid green when there is a
connection (or link) to a 10 Gbps Ethernet device or solid amber when there is
a connection (or link) to a 100/1000 Mbps Ethernet device on any of the RJ45
ports. The LED will blink green when a 10 Gbps port is active or blink amber
when a 100/1000 Mbps port is active. The LED will be off when there is no link
or activity.
SFP+ Ports:
The triangle LED indicates the Link/Act status of 10G SFP+ ports.
This LED will light solid green when there is a connection (or link) to a 10 Gbps
Ethernet device or solid amber when there is a connection (or link) to a 1 Gbps
Ethernet device at any at any of the SFP+ ports. The LED will blink green