D-Link DXS-3600-EM-STACK Hardware Installation Guide - Page 9

Front Panel Components, Description

Get D-Link DXS-3600-EM-STACK PDF manuals and user guides View all D-Link DXS-3600-EM-STACK manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide • • • Management Information Base (MIBs) for MIBII, Bridge MIB, SNMPv2 MIB, RMON MIB, RMONv2 MIB, Ether-like MIB, 802.3 MAU MIB, 802.1p MIB, IF MIB, RADIUS Authentication Client MIB, IGMPv3 MIB, RIPv2 MIB, IP Forward- ing Table MIB (CIDR), IPv4 Multicast Routing MIB, PIM MIB for IPv4, RADIUS Accounting Client MIB, Ping MIB, Trace out MIB, OSPFv2 MIB, VRRP MIB, Private MIB, Entity MIB. Front Panel Components The front panel of the switch consists of LED indicators, an SD card slot, an Out-Of-Band Management port (MGMT), a Console port, SFP+ ports and an open module slot. Figure 1-1 Front panel view of the DXS-3600-16S Figure 1-2 Front panel view of the DXS-3600-32S Ports that can be found on the front panel of this switch are listed in the table below. Port Description SD Card Slot This port can be used to insert an external SD memory card. The maximum capacity SD card that can be inserted into this port is 32Gb. Management port (MGMT) This port is a 10/100/1000Mbps Ethernet port with an RJ-45 connection. This OutOf-Band management port that can be used to configure this switch without being connected to the network. Console port This port is an RJ-45 connection port that can be used to connect to the Command Line Interface (CLI) of this switch for configuration, management and monitoring. This port uses a special console cable (included with the packing) with a DB9 interface to connect the Switch to a PC's COM port. 10 Gigabit ports This switch is equipped with SFP/SPF+/WDM ports. These ports can operate at 10Gbps speeds and support a vast collection of SFP/SFP+/WDM transceivers. Expansion Module Slot This slot can be equipped with 4 kinds of additional modules. These modules are not included and should be bought seperately. • DXS-3600-EM-4XT (Four 10GBASE-T Copper ports). • DXS-3600-EM-8T (Eight 1000BASE-T Copper ports). • DXS-3600-EM-4QXS (Four 40Gbps QSFP+ transceiver slots). • DXS-3600-EM-8XS (Eight 10Gbps SFP+ transceiver slots). • DXS-3600-EM-Stack (Two 120Gbps CXP Stacking ports). This module can only be used with the DXS-3600-32S. For a complete list of SFP/SFP+/WDM transceivers, that are compatible with this switch, refer to the "Product Specifications" section in Appendix A. 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
DXS-3600 Series 10GbE Layer 2/3 Switch Hardware Installation Guide
3
Front Panel Components
The front panel of the switch consists of LED indicators, an SD card slot, an Out-Of-Band Management port (MGMT), a
Console port, SFP+ ports and an open module slot.
Figure 1-1 Front panel view of the DXS-3600-16S
Figure 1-2 Front panel view of the DXS-3600-32S
Ports that can be found on the front panel of this switch are listed in the table below.
For a complete list of SFP/SFP+/WDM transceivers, that are compatible with this switch, refer to the “
Product
Specifications
” section in
Appendix A
.
• Management Information Base (MIBs) for MIBII, Bridge MIB, SNMPv2 MIB, RMON MIB, RMONv2 MIB, Ether-like
MIB, 802.3 MAU MIB, 802.1p MIB, IF MIB, RADIUS Authentication Client MIB, IGMPv3 MIB, RIPv2 MIB, IP Forward-
ing Table MIB (CIDR), IPv4 Multicast Routing MIB, PIM MIB for IPv4, RADIUS Accounting Client MIB, Ping MIB,
Trace out MIB, OSPFv2 MIB, VRRP MIB, Private MIB, Entity MIB.
Port
Description
SD Card Slot
This port can be used to insert an external SD memory card. The maximum capacity
SD card that can be inserted into this port is 32Gb.
Management port (MGMT)
This port is a 10/100/1000Mbps Ethernet port with an RJ-45 connection. This Out-
Of-Band management port that can be used to configure this switch without being
connected to the network.
Console port
This port is an RJ-45 connection port that can be used to connect to the Command
Line Interface (CLI) of this switch for configuration, management and monitoring.
This port uses a special console cable (included with the packing) with a DB9
interface to connect the Switch to a PC’s COM port.
10 Gigabit ports
This switch is equipped with SFP/SPF+/WDM ports. These ports can operate at
10Gbps speeds and support a vast collection of SFP/SFP+/WDM transceivers.
Expansion Module Slot
This slot can be equipped with 4 kinds of additional modules. These modules are not
included and should be bought seperately.
•
DXS-3600-EM-4XT
(Four 10GBASE-T Copper ports).
•
DXS-3600-EM-8T
(Eight 1000BASE-T Copper ports).
•
DXS-3600-EM-4QXS
(Four 40Gbps QSFP+ transceiver slots).
•
DXS-3600-EM-8XS
(Eight 10Gbps SFP+ transceiver slots).
• DXS-3600-EM-Stack
(Two 120Gbps CXP Stacking ports). This module can only
be used with the
DXS-3600-32S
.
•
•