Dacor DTF36FCS Installation Instructions/Use and Care Manual - Page 17

Flushing the Water Line

Get Dacor DTF36FCS PDF manuals and user guides View all Dacor DTF36FCS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Installation Instructions Flushing the Water Line After connecting the refrigerator to a water line or after replacing the water filter, make sure you flush the water system. You will need a container to press the back of the dispenser while catching at least 4 gallons of waste water. Flush the Water System: 1.To discharge air from the system, use a sturdy container to press and hold the water dispenser pad for 1-2 minutes until water comes from the dispenser. Water flow may be irregular at the beginning. As air is purged from the system, water may spurt out of the dispenser. After the air in the system is discharged, water flow will return to normal. • The first 10 glasses of water should not be consumed. • The first several glasses of water may be turbid when the filter is used for the first time. Therefore, do not consume the first several glasses of water. • Flushing air, debris, and bad water out of new water lines allows drinkable water as soon as possible. • Allow 1-2 days for the system to produce the required amount of ice. • Allow 12 hours for the refrigerator to cool down and chill water. • Dispense enough water every week to maintain a fresh water supply. IMPORTANT After 5 minutes of continuous flow, the dispenser will stop releasing water to avoid flooding. To restart the water flow, press the dispenser pad again. WARNING WARNING - Hazards or unsafe practices that COULD result in severe personal injury or death. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
15
Installation Instructions
After connecting the refrigerator to a water line or after
replacing the water filter, make sure you flush the water
system.
You will need a container to press the back of the
dispenser while catching at least 4 gallons of waste water.
Flush the Water System:
1. To discharge air from the system, use a sturdy container
to press and hold the water dispenser pad for 1-2
minutes until water comes from the dispenser. Water
flow may be irregular at the beginning. As air is purged
from the system, water may spurt out of the dispenser.
After the air in the system is discharged, water flow will
return to normal.
• The first 10 glasses of water should not be consumed.
• The first several glasses of water may be turbid when
the filter is used for the first time.
Therefore, do not
consume the first several glasses of water.
• Flushing air, debris, and bad water out of new water
lines allows drinkable water as soon as possible.
• Allow 1-2 days for the system to produce the required
amount of ice.
• Allow 12 hours for the refrigerator to cool down and
chill water.
• Dispense enough water every week to maintain a
fresh water supply.
Flushing the Water Line
IMPORTANT
After 5 minutes of continuous flow, the dispenser will stop
releasing water to avoid flooding.
To restart the water flow, press the dispenser pad again.
WARNING
WARNING –
Hazards or unsafe practices that
COULD
result in severe personal injury or death.