Danby DPAC9009 Use and Care Manual - Page 10

Auto-timer, Remote Control, Features

Get Danby DPAC9009 PDF manuals and user guides View all Danby DPAC9009 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

OPERATING INSTRUCTIONS (cont'd) AUTO-TIMER The AUTO-TIMER feature offers a unique selection of multiple choice, fully automatic on and/or off (start/stop) programs between 1-24 hours under any one mode of your Home Comfort unit. The programs are as follows: a) Auto-Off: Pre-select a time that will turn off the unit automatically (between 1-12hrs). b) Auto-On: Pre-select a time that will turn on the unit automatically (between 1-12hrs). c) Auto-On & Auto Off: Pre-select a time that will turn the unit ON / OFF automatically at specified times (between 1-12hrs). Note: These functions must be performed daily, as the program is automatically canceled/erased after the program has ended. REMOTE CONTROL FEATURES Control Buttons: 1) Power Switch 2) Mode 3) Fan Speed 4) On / Off Timer 5) Time / Temperature Set • Used for adjusting the timer and temperature. • The default display on control panel is room temperature. • When key is pressed in cool mode, the set temperature is displayed and may be adjusted. After 10 seconds the display will revert back to room temperature. • Timer setting is available from 1-24 hours by pressing the key To operate the hand held remote control you will require two "AAA" Alkaline batteries (included). Batteries should be replaced when: a) No signal (beep) is heard when attempting to program the main unit. b) The main unit does not respond to a command issued by the remote control. Battery replacement: 1) Slide the rear cover on the remote in the direction of the arrow. Continue pulling (gently) until the cover separates completely from the unit. 2) Insert (2) batteries (AAA) following the same orientation (polarity) depicted inside the battery chamber (+ / -). 3) Re-install rear cover. 4) If the remote control will not be used for extended periods of time (vacations, etc.), batteries should be removed. The remote operates within a range of 8 meters (26 ft.) from the receiver located inside the main unit. Any obstruction between the receiver and remote may cause signal interference, limiting the ability to program the unit. Notes: 1) Do not drop the remote control. 2) Do not place the remote control in a location exposed to direct sunlight. 3) The remote control should be placed about 1 meter or more away from TV, or any electrical appliances. This Class B digital apparatus complies with canadian ICES-003. 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
OPERATING INSTRUCTIONS (cont’d)
AUTO-TIMER
The AUTO-TIMER feature offers a unique selection of multiple
choice, fully automatic on and/or off (start/stop) programs between
1-24 hours under any one mode of your Home Comfort unit.
The programs are as follows:
a)
Auto-Off: Pre-select a time that will turn off the unit automatically (between 1-12hrs).
b)
Auto-On: Pre-select a time that will turn on the unit automatically (between 1-12hrs).
c)
Auto-On & Auto Off: Pre-select a time that will turn the unit ON / OFF automatically
at specified times (between 1-12hrs).
Note: These functions must be performed daily, as the program is automatically
canceled/erased after the program has ended.
9
REMOTE CONTROL
FEATURES
Control Buttons:
1)
Power Switch
2)
Mode
3)
Fan Speed
4)
On / Off Timer
5)
Time / Temperature Set
• Used for adjusting the timer and
temperature.
• The default display on control panel is
room temperature.
• When
key is pressed in
cool mode, the set temperature is
displayed and may be adjusted. After 10
seconds the display will revert back to
room temperature.
• Timer setting is available from 1-24
hours by pressing the key
To operate the hand held remote control
you will require two “AAA” Alkaline
batteries (included).
Batteries should be replaced when:
a)
No signal (beep) is heard when attempting to program the main unit.
b)
The main unit does not respond to a command issued by the remote control.
Battery replacement:
1)
Slide the rear cover on the remote in the direction of the arrow. Continue pulling (gently)
until the cover separates completely from the unit.
2)
Insert (2) batteries (AAA) following the same orientation (polarity) depicted inside the
battery chamber (+ / -).
3)
Re-install rear cover.
4)
If the remote control will not be used for extended periods of time (vacations, etc.),
batteries should be removed.
The remote operates within a range of 8 meters (26 ft.) from the receiver located inside
the main unit. Any obstruction between the receiver and remote may cause signal
interference, limiting the ability to program the unit.
Notes:
1)
Do not drop the remote control.
2)
Do not place the remote control in a location exposed to direct sunlight.
3)
The remote control should be placed about 1 meter or more away from TV, or any
electrical appliances.
This Class B digital apparatus complies with canadian ICES-003.