Dell Alienware m16 R1 AMD Service Manual - Page 18

Installing the battery, Steps, Prerequisites, About this task, Next steps

Get Dell Alienware m16 R1 AMD PDF manuals and user guides View all Dell Alienware m16 R1 AMD manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

Steps 1. Peel the tape that secures the battery cable to the battery. 2. Disconnect the battery cable from the system board. NOTE: This step is applicable only if the battery cable has not been disconnected. 3. Remove the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly. 4. Remove the four screws (M2x3.5) that secures the battery to the palm-rest and keyboard assembly. 5. Lift the battery off the palm-rest and keyboard assembly. Installing the battery Prerequisites If you are replacing a component, remove the existing component before performing the installation process. About this task The following image(s) indicate the location of the battery and provides a visual representation of the installation procedure. Steps 1. Using the alignment posts, place the battery on the palm-rest and keyboard assembly. 2. Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly. 3. Replace the four screws (M2x3.5) that secure the battery to the palm-rest and keyboard assembly. 4. Replace the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly. 5. Connect the battery cable to the system board. 6. Adhere the tape that secures the battery cable to the battery. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
Steps
1.
Peel the tape that secures the battery cable to the battery.
2.
Disconnect the battery cable from the system board.
NOTE:
This step is applicable only if the battery cable has not been disconnected.
3.
Remove the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly.
4.
Remove the four screws (M2x3.5) that secures the battery to the palm-rest and keyboard assembly.
5.
Lift the battery off the palm-rest and keyboard assembly.
Installing the battery
Prerequisites
If you are replacing a component, remove the existing component before performing the installation process.
About this task
The following image(s) indicate the location of the battery and provides a visual representation of the installation procedure.
Steps
1.
Using the alignment posts, place the battery on the palm-rest and keyboard assembly.
2.
Align the screw holes on the battery with the screw holes on the palm-rest and keyboard assembly.
3.
Replace the four screws (M2x3.5) that secure the battery to the palm-rest and keyboard assembly.
4.
Replace the four screws (M2x4) that secure the battery to the palm-rest and keyboard assembly.
5.
Connect the battery cable to the system board.
6.
Adhere the tape that secures the battery cable to the battery.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
18