Dell Inspiron 13 5320 Service Manual - Page 39

Steps, To avoid damaging the display, do not slide the palm-rest and keyboard assembly over

Get Dell Inspiron 13 5320 PDF manuals and user guides View all Dell Inspiron 13 5320 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 39 highlights

Steps 1. Place the display assembly on a clean and flat surface with the display panel facing up. 2. Align and place the palm-rest and keyboard assembly under the display hinges. CAUTION: To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display assembly. 3. Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the palm-rest and keyboard assembly. 4. Replace the two screws (M2x3) that secure the left-display hinge to the palm-rest and keyboard assembly. 5. Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the USB Type-C port bracket and the palm-rest and keyboard assembly. 6. Replace the two screws (M2x3) that secure the right-display hinge to the palm-rest and keyboard assembly. 7. Connect the display cable to the connector on the system board and close the latch to secure the cable. 8. Adhere the tape that secures the display cable to the system board. 9. Adhere the tape that secures the display-cable connector latch to the system board. Next steps 1. Install the base cover. 2. Follow the procedure in After working inside your computer. Removing and installing components 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Steps
1.
Place the display assembly on a clean and flat surface with the display panel facing up.
2.
Align and place the palm-rest and keyboard assembly under the display hinges.
CAUTION:
To avoid damaging the display, do not slide the palm-rest and keyboard assembly over the display
assembly.
3.
Close the left-display hinge and align the screw holes on the left-display hinge with the screw holes on the palm-rest and
keyboard assembly.
4.
Replace the two screws (M2x3) that secure the left-display hinge to the palm-rest and keyboard assembly.
5.
Close the right-display hinge and align the screw holes on the right-display hinge with the screw holes on the USB Type-C
port bracket and the palm-rest and keyboard assembly.
6.
Replace the two screws (M2x3) that secure the right-display hinge to the palm-rest and keyboard assembly.
7.
Connect the display cable to the connector on the system board and close the latch to secure the cable.
8.
Adhere the tape that secures the display cable to the system board.
9.
Adhere the tape that secures the display-cable connector latch to the system board.
Next steps
1.
Install the
base cover
.
2.
Follow the procedure in
After working inside your computer
.
Removing and installing components
39